manualshive.com logo in svg

Heat & Glo VRT-BK-N-AUB, Руководство пользователя

Поделиться
Скачать
Heat & Glo VRT-BK-N-AUB Скачать руководство пользователя страница 1

Heat & Glo  •  VRT-AUB  •  2123-980_R14  •  12/14

1

Owner’s Manual

Installation and Operation

WARNING: If the information in these instructions 

is not followed exactly, a fire or explosion may 

result causing property damage, personal injury, 

or death.

This appliance has been supplied with an integral barrier to 

prevent direct contact with the fixed glass panel. DO NOT 

operate the appliance with the barrier removed. 

Contact your dealer or Hearth & Home Technologies if the barrier 

is not present or help is needed to properly install one.

HOT SURFACES

! 

Glass and other surfaces are hot during 

operation AND cool down.

Hot glass will cause burns.

• 

DO NOT

 touch glass until it is cooled

•  NEVER allow children to touch glass

•  Keep children away

This is a room sealed appliance and no other ventilation is 

required than what is provided.

DO NOT DISCARD THIS MANUAL

NOTICE

•  Leave  this  manual  with 

party responsible for use 

and operation.

DO NO

T

DISCARD

•  Important  operating 

and maintenance 

instructions included.

•  Read, understand and follow 

these instructions for safe 

installation and operation.

VRTIKL-AUB

FREESTANDING STOVE

MODELS:

VRT-BZ-N-AUB
VRT-BZ-P-AUB
VRT-GY-N-AUB
VRT-GY-P-AUB
VRT-BK-N-AUB

SAI Global

Ref No GSCS20166

AS4553:2008

• 

DO NOT

 USE OR STORE FLAMMABLE MATERIALS 

NEAR THIS APPLIANCE.

• 

DO NOT

 SPRAY AEROSOLS IN THE VICINITY OF 

THIS APPLIANCE WHILE IT IS IN OPERATION.

•  What to do if you smell gas 

 

- 

DO NOT

 try to light any appliance.

- 

DO NOT

 touch any electrical switch. 

- 

DO NOT

 use any phone in your building.

-  Immediately call your gas supplier from a neighbor’s 

phone. Follow the gas supplier’s instructions.

-  If you cannot reach your gas supplier, call the fire 

department.

•  Installation and service must be performed by a qualified 

installer, service agency, or the gas supplier.

WARNING!  DO NOT modify this appliance. 

WARNING

!

•  CAREFULLY SUPERVISE children in same room as fireplace.
•  Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other flammable 

materials.

•  DO NOT 

place articles on or against this appliance.

•  Keep  clothing,  furniture,  draperies  and  other  flammable 

materials away.

!

Содержание VRT-BK-N-AUB













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды