Heat & Glo Balanced Flue Gas Fireplace SOHO-CE Скачать руководство пользователя страница 5

Страница: 5 / 39

Heat & Glo • Soho-CE • 2111-900 Rev. D • 6/07

A. Design and Installation Considerations

Heat & Glo balanced fl ue gas appliances are designed
to operate with all combustion air siphoned from outside
of the building and all exhaust gases expelled to the out-
side. No additional outside air source is required.

Getting Started

C. Inspect Appliance and Components

When planning an appliance installation, it’s necessary to
determine the following information before installing:

• Where the appliance is to be installed.

• The fl ue system confi guration to be used.

• Gas supply piping.

• Framing and fi nishing details.

B. Tools and Supplies Needed

Before beginning the installation be sure that the following
tools and building supplies are available.

Reciprocating saw

Framing material

Pliers

Hi temp caulking material

Hammer

Gloves

Phillips screwdriver

Framing square

Flat blade screwdriver Electric drill and bits (1/4 in.)

Plumb line

Safety glasses

Level

Manometer

Tape measure

Voltmeter

Noncorrosive leak check solution

One 1/4 inch female connection (for optional fan).

1/2 - 3/4 inch length, #6 or #8 Self-drilling screws

• Carefully remove the appliance and components from

the packaging.

• The fl ue system components and trim doors are shipped

in separate packages.

• The logs are packaged separately inside the fi replace

and must be fi eld installed.

• Report to your dealer any parts damaged in shipment,

particularly the condition of the glass.

• Read all of the instructions before starting the insta-

llation. Follow these instructions carefully during the
installation to ensure maximum safety and benefi t.

Check building codes prior to installation.

• Installation MUST comply with local, regional, state and

national codes and regulations.

• Consult local building, fi re offi cials or authorities having jurisdic-

tion about restrictions, installation inspection, and permits.

CAUTION

Inspect appliance and components for damage.
Damaged parts may impair safe operation.

• Do NOT install damaged components.

• Do NOT install incomplete components.

• Do NOT install substitute components.

Report damaged parts to dealer.

Hearth & Home Technologies disclaims any
responsibility for, and the warranty will be voided
by, the following actions:

• Installation and use of any damaged appliance or fl ue

system component.

• Modifi cation of the appliance or fl ue system.

• Installation other than as instructed by Hearth & Home

Technologies.

• Improper positioning of the gas logs or the glass door.

• Installation and/or use of any component part not approved

by Hearth & Home Technologies.

Any such action may cause a fi re hazard.

WARNING

Содержание Balanced Flue Gas Fireplace SOHO-CE








































Результаты поиска

Содержание Balanced Flue Gas Fireplace SOHO-CE

Отзывы:

Похожие инструкции для Balanced Flue Gas Fireplace SOHO-CE

Бренды по названию

Популярные бренды

Heat & Glo Balanced Flue Gas Fireplace SOHO-CE, Руководство по установке

Результаты поиска

Содержание Balanced Flue Gas Fireplace SOHO-CE

Отзывы:

Похожие инструкции для Balanced Flue Gas Fireplace SOHO-CE

Бренды по названию

Популярные бренды