background image

Heat & Glo  •  6000PLUS  •  2063-900  Rev. E  •  11/05

3

TABLE OF CONTENTS

Safety and Warning Information

. ............................................... 2

Service Parts Lists

. .................................................................... 4

Section 1: Approvals and Codes

. .............................................. 7

Appliance Certification................................................................... 7
Installation Codes.......................................................................... 7
High Altitude Installations ............................................................... 7

Section 2: Getting Started ......................................................... 8

Introducing the Heat & Glo Gas Fireplaces ................................... 8
Pre-installation Preparation ........................................................... 8

Section 3: Installing the Fireplace

. ......................................... 10

Constructing the Fireplace Chase .............................................. 10
Step 1

Locating the Fireplace ................................................. 10

Step 2

Framing the Fireplace................................................... 11

Step 3

Installing the Vent System............................................. 11

Step 4

Securing the Fireplace.................................................. 11

Step 5

The Gas Control Systems ............................................ 11

Step 6

The Gas Supply Line ................................................... 12

Step 7

Gas Pressure Requirements ........................................ 12

Step 8

Wiring the Fireplace .................................................... 13

Step 9

Sequence of Operation................................................ 15

Step 10 Finishing ...................................................................... 16
Step 11 Installing Trim, Logs, and Ember Material.................... 16

Installing the Trim......................................................... 16
Positioning the Logs .................................................... 16
Shutter Settings ........................................................... 16
Placing the Ember Material.......................................... 16
Glass Specifications ..................................................... 17

Step 12 Before Lighting the Fireplace ....................................... 17
Step 13 Lighting the Fireplace .................................................. 18
After the Installation ..................................................................... 18

Section 4:  Maintaining and Servicing Your Fireplace

. ........ 19

Section 5:  IPI Troubleshooting Guide

. .................................. 20

Î

 =  Contains updated information.

Î

Î

Содержание 6000PLUS




















Отзывы: