Heat & Glo 6000PLUS Скачать руководство пользователя страница 10

Страница: 10 / 19

Heat & Glo • 6000PLUS • 2063-900 Rev. E • 11/05

Step 8. Wiring the Fireplace

NOTE: Electrical wiring must be installed by a licensed

electrician.

CAUTION: DISCONNECT REMOTE CONTROLS IF AB-

SENT FOR EXTENDED TIME PERIODS TO PREVENT

ACCIDENTAL FIREPLACE OPERATION.

Wall Switch

Position the wall switch in the desired position on the wall.

An assembly of 18 ft of 20 AWG is provided with the fire-

place to connect the wall switch to the appliance. Instead of

the supplied assembly, wire with a length of 25 ft or less and

a gauge of 20 AWG through 14 AWG is acceptable. The

wire needs a jacket with a temperature rating of 140

F (60

or higher. At the appliance connect the wire to the ON/OFF

switch pigtails.

Figure 7. Fan Wiring Diagram

WARNING: DO NOT CONNECT 110-120 VAC

TO THE WALL SWITCH OR THE CONTROL

VALVE WILL BE DESTROYED.

CAUTION: LABEL ALL WIRES PRIOR TO DISCON-

NECTION WHEN SERVICING CONTROLS. WIRING

ERRORS CAN CAUSE IMPROPER AND DANGEROUS

OPERATION. VERIFY PROPER OPERATION AFTER

SERVICING.

NOTE: IF ANY OF THE ORIGINAL WIRE

AS SUPPLIED WITH THE APPLIANCE

MUST BE REPLACED, IT MUST BE

REPLACED WITH TYPE 105 C RATED WIRE.

JUNCTION BOX

VARIABLE SPEED CONTROL

TEMPERATURE

SENSOR SWITCH

WHT

GRN

BLK

110-120 VAC

BLOWER

BLOWER RECEPTACLE

BLK

WHT

GROUND

WHT

BLK

BLOWER

SENSOR

SWITCH

“FAN”

RECEPTACLE

SPEED

CONTROL

Содержание 6000PLUS




















Результаты поиска

Содержание 6000PLUS

Отзывы:

Бренды по названию

Популярные бренды

Heat & Glo 6000PLUS, Руководство пользователя

Результаты поиска

Содержание 6000PLUS

Отзывы:

Бренды по названию

Популярные бренды