Heartland ROCKPORT Скачать руководство пользователя страница 5

Страница: 5 / 68

COMPLETING YOUR SHED

You will need these additional materials:

OPTIONAL MATERIALS

DRIP EDGE ..................... 60 Feet

#15 ROOFING FELT

To cover 170 Sq. Ft. of roof area.

1" GALVANIZED ROOFING NAILS.........1/4 Lb

For roofing felt.

REFER TO THE BACK OF THIS MANUAL AND THE MANUFACTURER’S INSTRUCTIONS FOR

INSTALLATION OF SHINGLES, DRIP EDGE AND FELT.

3-TAB SHINGLES ............................ 6 Bundles

PAINT FOR SIDING .......................... 2 Gallons

Use 100% acrylic latex exterior paint. (2) coats recommended.

CAULK ................................................. 3 Tubes

Use acrylic latex exterior caulk that is paintable.

1" GALVANIZED ROOFING NAILS.... 3 Lbs

For shingles.

PAINT FOR TRIM .............................2 Quarts

Use 100% acrylic latex exterior paint.

You must caulk completely around window frame to

validate your warranty. Use a paintable exterior rated caulk.

REINFORCED WOOD FLOOR FRAME (OPTIONAL)

IMPORTANT!

This floor has been designed for general use. Depending on your specific use you may want to construct a heavy

duty floor frame by adding additional floor joists (shown below as shaded). Below is a list of additional materials (not included):

2 x 4 x 8' (5 x 10 x 96 cm) Treated Lumber

Cut to 2 x 4 x 93" (5 x 10 x 236,2 cm)

ea. 3" (7,6 cm) Hot Dipped Galvanized Nails

Optional 12" (30,5 cm) spacing

WOOD FLOOR FRAME

FOUNDATION OR FLOOR MATERIALS

ADDITIONAL MATERIALS

• This shed

does not

include any floor or leveling materials.

• See the FLOOR LEVELING section on page 7 for recommended methods and suggested materials to properly level your floor,

as this will vary depending on your specific site.

NOTE: Use a minimum of 5/8" (1,6 cm) Oriented Strand Board (OSB)

FLOOR PANELS

2" (5,1 cm)

1 lb. of 2" (5,1 cm) Hot Dipped Galvanized Box-Type Nails.

5/8" x 48" x 96"

(1,6 x 121,9 x 243,8 cm)

•

Cut 1 panel to: 45" x 96"

MATERIAL REQUIRED:

Use only wood treated for ground contact and fasteners approved for use with treated wood.

Hot Dipped Galvanized Box-Type Nails.

3" (7,6 cm)

x40

x10

2 x 4 x 93" (5,1 x 10,2 x 236,2 cm)

2 x 4 x 141" (5,1 x 10,2 x 358,1 cm)

Standard 16" (40,6 cm) spacing

Содержание ROCKPORT





































































Результаты поиска

Содержание ROCKPORT

Отзывы:

Бренды по названию

Популярные бренды

Heartland ROCKPORT, Инструкция по сборке

Результаты поиска

Содержание ROCKPORT

Отзывы:

Бренды по названию

Популярные бренды