HearthStone Clydesdale 8490 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 35

background image

HearthStone

Quality Home Heating Products Inc

®

Clydesdale Model 8490

27

Page: 3 of 10

Step Three

: Install the door handle onto the latch. The wooden handle, ¼” x 2-3/4” bolt, and ¼” lock

washer are located in a plastic zip back removed from the firebox in step one. Place the washer onto the
bolt and then push the bolt through the handle. Turn the threads of the bolt onto the latch and tighten
with a screwdriver. Handle has been installed in photo #1.

Reversing the door to open from the right hand side;

It is possible to reverse the door,

if

desired

. It will be shipped from the factory opening on the left hand side. If you do not want to reverse

the door, skip to the next step. To reverse the door, you will have to first remove the front façade.
Locate the clips on the back of the façade – these are on the top right and left side of the façade (see
photo #5). Loosen the retaining screws with a phillips screwdriver. This will allow you to lift the façade
up and off the front of the firebox.

Façade Clips

To switch the door to open from the right hand side, remove the two phillips head screws holding the
door hinges onto the stove (see photo 6).

NOTE

: Use caution when removing the last screw as the door

will now be disconnected from the body and will be loose in your hand. Make sure to retain the two
hinge rivets
for reuse. After removing the door, use the phillips screwdriver to remove the two screws that hold the
door catch to the body of the stove (photo 7).

NOTE

: Save the spacer washers that are behind the door

catch for reuse. Remove the two screws where the door hinges will be attached on the left side and
rotate the door 180 degrees. Line the hinges up with these holes and attach the door by inserted the
hinge screws and tighten them to the stove with the phillips screwdriver. Reattach the door catch on the
opposite side of the stove by reusing the retaining screws and spacer washers.

P

HOTO

#5

One of the two retaining
clips and screws on the back
of the façade.

«
...
26
27
28
29
30
...
»

Содержание Clydesdale 8490




































Отзывы:

Нет отзывов

Похожие инструкции для Clydesdale 8490

Бренд: Valor Страницы: 14

CLEARion Series

Бренд: Napoleon Страницы: 30

Бренд: Superior Страницы: 36

Бренд: Hiland Страницы: 3

Бренд: Evonic Fires Страницы: 44

Бренд: Kingsman Страницы: 17

Ascent Linear BL56

Бренд: Napoleon Страницы: 132

Бренд: Twin-Star International Страницы: 28

Бренд: Uniflame Страницы: 20

Бренд: Quadra-Fire Страницы: 41

C11810LP Sedona

Бренд: Real Flame Страницы: 48

Marquis MCVP42LP

Бренд: Kingsman Fireplaces Страницы: 75

Бренд: Majestic Страницы: 24

Бренд: Fire Sense Страницы: 18

Crea7ion EvoPlus Thales

Бренд: GlammFire Страницы: 20

Бренд: Home Decorators Collection Страницы: 41

Бренд: Valor Страницы: 4

Бренд: VISION FUTURA Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды