Health in motion INSPIRE DUAL AB BACK Скачать руководство пользователя страница 30

Страница: 30 / 31

Page 27

MAINTENANCE SCHEDULE

ROUTINE

COMMERCIAL/

LIGHT COMMERCIAL

MAINTENANCE

HOME

MAINTENANCE

ENTRY DATE

Inspect: Links, Pull

Pins, Spring Clips,

Swivels, Weight Stack

Pins.

DAILY

WEEKLY

Clean: Upholstery.

DAILY

WEEKLY

Inspect: Cables and

their Fittings for wear

or looseness.

DAILY

WEEKLY

Inspect: Tautness of

all Shrouds.

DAILY

WEEKLY

Inspect: Accessory

Bars and Handles.

WEEKLY

3 MONTHS

Inspect: All Decals.

WEEKLY

3 MONTHS

Inspect: All Nuts and

Bolts. Tighten if

Needed.

WEEKLY

3 MONTHS

Inspect: Anti-Skid

surfaces.

WEEKLY

3 MONTHS

Clean and Lubricate:

Guide Rods with a

Teflon based

lubricant.

WEEKLY

3 MONTHS

Lubricate: Seat

Sleeves, all Plastic

Slides, and Linear

Bearings.

WEEKLY

3 MONTHS

Clean and Wax: All

Glossy Finishes.

6 MONTHS

YEARLY

Replace: Cables,

Belts, and Connecting

Parts.

YEARLY

2 YEARS

Содержание INSPIRE DUAL AB BACK
































Результаты поиска

Содержание INSPIRE DUAL AB BACK

Отзывы:

Бренды по названию

Популярные бренды

Health in motion INSPIRE DUAL AB BACK, Руководство по сборке и эксплуатации

Результаты поиска

Содержание INSPIRE DUAL AB BACK

Отзывы:

Бренды по названию

Популярные бренды