background image

Doc No. XG-0042   Rev No. 042808

 

12

Over Temperature Alarm:  

The X-Caliber will turn off and go into over temperature alarm when the temperature in the pump exceeds 140º F 
(70ºC). Most probable cause is too high of an ambient temperature. 
 

Over Current Alarm: 

The X-Caliber pump continuously monitors the input current levels. If the current level reaches 60 Amps, the pump 
will turn off and go into Over Current Alarm. Most probable cause is debris stuck in the pump. 
 

Over Pressure Alarm: 

The X-caliber can be used as a pressure booster and thus be supplied with pressurized water. To prevent the 
pump from exceeding its maximum operating pressure of 110 psi (7.5 Bar), the pump will turn off and go into over 
pressure alarm if this pressure is exceeded.   

 
Anti-Flooding Alarm: 

The X-Caliber has an optional anti-flooding routine that will recognize when the pump is running at the same RPM, 
input power, and pressure for 30 minutes, turn the pump off, and go into alarm. The pump is shipped without this 
routine enabled. 
 
To enable the anti-flooding protection, push and hold the on/off switch for 20 seconds while the pump is running. 
Release the on/off switch when the yellow LED begins to flash.  
To disable the anti-flooding protection, push and hold the on/off switch for 20 seconds while the pump is 
running. Release the on/off switch when the yellow LED stops flashing and returns to a steady yellow illumination.  

 
Maintenance: 

The X-Caliber is designed to be a maintenance free water pressure pump. It is recommended to check the inlet 
strainer monthly for any accumulation of debris. 
 

Winterization: 

Freezing will damage the pump and connected plumbing. Use the following procedure to winterize your X-Caliber 
water pump. 
 

1.  Open faucet and allow pump to run and empty freshwater tank. 
2.  Remove drain plug on front of pump and allow water to drain water from pump body. 
3.  Do not use Automotive Antifreeze to winterize potable water systems as it is very poisonous and may 

cause serious injury or death. 

 

X-Caliber Installation Accessories (sold separately):

 

 

IS-1000L   1” FPT   High Flow Inlet Strainer 
IS-1000L   1” BSP  High Flow Inlet Strainer 
IS-750 

 ¾” FPT  High Flow Inlet Strainer 

IS-1000S  1” FPT    Compact High Flow Inlet Strainer 

 

BPH-750   

¾” 19mm ID Banzai pipeline Potable Water Suction /Pressure Hose 

BPH-1000 

1” 25 mm ID Banzai Pipeline Potable Water Suction/Pressure Hose 

 

1436-007                ¾” MPT x ¾” (19mm) Straight PVC Hose Adapter 
1436-102                 ¾” MPT x 1”  (25mm) Straight PVC Hose Adapter 

 

1413-131  

¾” MPT x 1”  (25mm) 90º PVC Hose Adapter 

1413-007                   ¾” MPT x ¾” (19mm) 90º PVC Hose Adapter 

 

PT-102 

 

Headhunter Pressure Accumulator Tank w/ optional X-Caliber mounting bracket 

 

Содержание X-CALIBER XR-124

















Отзывы: