background image

IS2300 Rev D

 

 

USE ONLY HAYWARD GENUINE REPLACEMENT 

PARTS 

    

1

 

 

MaxFlo XL

™ 

Pump Series 

Owner’s Manual 

 

IMPORTANT SAFETY INSTRUCTIONS 

 

The Hayward MaxFlo XL is a series of high technology self-priming pumps that combine 
performance, dependability and value with durable construction.  Designed for pools of all types 
and sizes, MaxFlo XL features 1 1/2” x 2” union connections to match a variety of plumbing 
configurations and a cam and ramp strainer cover that seals with less than a quarter turn.  The 
MaxFlo XL is an ideal choice for both new construction or as a replacement pump. 

Hayward Pool Products

620 Division Street, Elizabeth, NJ 07207 

Phone: (908) 355-7995 

www.hayward.com

 

 

Contents 

Full Table of Contents……..…..…2 

General Product Warnings…….…3 

Installation and Wiring……..….…5 

Start up and Operation…………..9 

Shaft Seal Replacement………...10 

Replacement Parts………..…….…13 

Warrantee…………………….…..……15 

Registration………………….………..16 

Basic safety precautions should always be followed, including the following: Failure to follow 

instructions can cause severe injury and/or death. 

 

This is the safety-alert symbol. When you see this symbol on your equipment or in this manual, look for 

one of the following signal words and be alert to the potential for personal injury. 

 

WARNING warns about hazards that could cause serious personal injury, death or major property 

damage and if ignored presents a potential hazard. 

 

CAUTION warns about hazards that will or can cause minor or moderate personal injury and/or property 

damage and if ignored presents a potential hazard.  It can also make consumers aware of actions that are 

unpredictable and unsafe.

   

The NOTICE label indicates special instructions that are important but not related to hazards.

 

Содержание SP2305X7

















Отзывы: