Hayward Pro Logic PL-P-4-CUL Скачать руководство пользователя

Страница: 8 / 36

2. Mounting the Equipment

Pro Logic Control Center

The Pro Logic is contained in a raintight enclosure that is suitable for outdoor mounting. The control must be mounted

a minimum of 5 ft. (2 meters) horizontal distance from the pool/spa (or more, if local codes require). The Control

Center is designed to mount vertically on a flat surface with the knockouts facing downward. Because the enclosure

also acts as a heat sink (disperses heat from inside the box), it is important not to block the four sides of the control. Do

not mount the Pro Logic inside a panel or tightly enclosed area.

When selecting a location, note that the standard cables supplied with the Turbo Cell, flow switch, temperature sen-

sors, and valve actuators (if applicable) are all 15 ft. (5m) long.

Temperature Sensors

Three sensors are included with the Pro Logic. A water sensor and an air sensor must be installed at all times for

proper operation. A solar sensor is required if the solar function is enabled.

Water Sensor

This sensor is used to measure the pool/spa temperature and is installed in the filtration plumbing after the filter but

before either the solar or conventionally fueled heaters—refer to the plumbing overview diagram.

1. Drill a 3/8” (10mm) diameter hole in the PVC piping and remove all chips and burrs.

2. Insert sensor until O-ring collar sits flush on the hole.

3. Position hose clamp over the sensor and gently tighten until O-ring makes an adequate seal. Do not overtighten.
4. For maximum temperature accuracy, cover the sensor and 3” (6cm) of pipe on either side with insulation and

white paint.

Air Sensor

Mount the air sensor outdoors.

IMPORTANT: Mount the air sensor out of direct sunlight.

Solar Sensor

For solar applications, mount the sensor near the solar collector array so that it is exposed to the same sunlight as the

collectors. Use additional cable (20 AWG) if necessary.

Optional Chlorination Function

The PL-P-4 model requires the use of a chlorinator cell and plumbing kit to provide pool chlorination. These items are

not included with the Pro Logic and can be purchased separately at your local Hayward dealer. Choose a chlorinator

cell model based on the size of your pool. The following models are available:

T-CELL-15 for pools up to 40,000 gallons

T-CELL-9 for pools up to 25,000 gallons

T-CELL-3 for pools up to 15,000 gallons

In addition to the chlorinator cell, a plumbing kit (P-KIT) must be purchased. This kit contains the cell unions and flow

switch. Refer to pages 8 and 18 for plumbing and wiring instructions.

Optional AQL-CHEM ORP and pH Sensing Kit

The AQL-CHEM is an ORP and pH sensing kit for the Pro Logic. When chlorination is enabled (requires chlorinator

cell and P-KIT), the Pro Logic senses the pool's ORP and pH levels and generates the correct amount of chlorine to

keep your pool properly sanitized. Wiring and plumbing requirements for the AQL-CHEM should be considered

before installing the Pro Logic. Refer to the AQL-CHEM manual for specific installation information.

Lights Interlock

If enabled, this feature will override the function (Manual On/Off, Countdown Timer, Timeclock) selected
above and turn the lights relay off when: filter pump is off, first 3 minutes of filter pump operation (allows
the pump to prime and get water flowing), when the pool/spa suction return valves are in any position
other than “pool only”, or for the first 3 minutes after solar turns on (allows air in the solar panels to be
purged). Interlock is not available for solar, low speed filter pump, super chlorinate or dimmer.

Lights External Input Interlock

When Lights External Input Interlock is enabled, the lights output will be forced off when the external input
is active. This will have precedence over freeze protection. Lights External Input Interlock is not available
for solar, low speed filter pump, dimmer, super chlorinate, or pH dispense functions.

Lights Freeze Protection

This function helps protect equipment that is wired to the lights relay against freeze damage. If Freeze
Protection is enabled and the AIR temperature sensor falls below the selected freeze temperature threshold,
the Pro Logic will energize the lights relay. IMPORTANT: this only enables operation of the lights relay
during freeze--see the “Filter Pump Config.” menu to enable freeze protection for the main circulation
system.

Lights Pump Speed

This is the speed of the filter pump when the Lights output is on. The default selection is “Settings Menu”.
This is the speed of the pump that has been selected in the Settings Menu for normal filter operation. If an
alternate speed is desired when the Lights output is on, push “+” or “-” and select from “Filter Lowest” to
“Filter Highest” in 5% increments.

NOTE: The configuration parameters for the Aux2 output are the same as shown below for Aux1.

Aux1 Pump Spd

Settings Menu

Select Settings Menu (default) or desired pump speed (Filter Lowest to Highest)
Move to previous/next configuration menu

if filter pump is set to variable speed

and the relay type is set to standard

Aux1 Config.

+ to view/change

Aux1 Function

Manual On/Off

Aux1 Relay

Standard