background image

IMPORTANT SAFETY INSTRUCTIONS

When using this electrical equipment, basic safety precautions should always be
followed, including the following:

READ AND FOLLOW ALL INSTRUCTIONS

!

WARNING:  Disconnect all AC power during installation.

!

WARNING:  Water in excess of 100 degrees Fahrenheit may be

hazardous to your health.

!

WARNING:  To reduce the risk of injury, do not permit children to

use this product unless they are closely supervised at all times.

A green colored terminal marked “Grounding” is located inside the wiring
compartment.  To reduce the risk of electric shock, this terminal must be
connected to the grounding means provided in the electric supply service
panel with a continuous copper wire equivalent in size to the circuit conductors
supplying the equipment.

One bonding lug for US models (two for Canadian models) is provided on the
external surface.  To reduce the risk of electric shock, connect the local
common bonding grid in the area of the swimming pool, spa, or hot tub to
these terminals with an insulated or bare copper conductor not smaller than 8
AWG US / 6 AWG Canada.

All field installed metal components such as rails, ladders, drains, or other
similar hardware within 3 meters of the pool, spa or hot tub shall be bonded to
the equipment grounding bus with copper conductors not smaller than 8 AWG
US / 6 AWG Canada.

SAVE THESE INSTRUCTIONS

32

LIMITED WARRANTY (effective 04/01/09) 

Hayward/Goldline warrants its Pro Logic and E-Command

pool automation products as well as its Aqua Rite, Aqua Rite Pro, Aqua Plus and SwimPure chlorination products

to be free of defects in materials and workmanship, under normal use and service, for a period of three (3) years.

Hayward/Goldline also warrants its Aqua Trol chlorination products to be free of defects in materials and work-

manship, under normal use and service for a period of one (1) year.  These warranties are applicable from the initial

date of installation on private residential swimming pools in the US and Canada.

Hayward/Goldline warrants all the above-identified pool automation and chlorination products installed on com-

mercial swimming pools and on swimming pools outside of the US and Canada for a period of one (1) year.

Likewise,   Hayward/Goldline warrants all accessories and replacement parts for the above-identified pool auto-

mation and chlorination products for a period of one (1) year.  Each of these warranties is not transferable and

applies only to the original owner.

Proof of purchase is required for warranty service.  If written proof of purchase is not provided, the manufacturing

date code will be the sole determinant of the date of installation of the product.  To obtain warranty service or

repair, please contact the place of purchase or the nearest Hayward/Goldline authorized warranty service center.

For more information on authorized service centers please contact the Hayward/Goldline Technical Service Sup-

port Center (61 Whitecap Road, North Kingstown RI, 02852) or visit the Goldline web site at

www.goldlinecontrols.com or the Hayward website at www.haywardnet.com.

WARRANTY EXCLUSIONS

:

1. Material supplied or workmanship performed by others in process of installation.

2. Damage resulting from improper installation including installation on pools larger than the product rating.

3. Problems resulting from failure to install, operate or maintain the product(s) in accordance with the recommen-

dations contained in the owners manual(s).

4. Problems resulting from failure to maintain pool water chemistry in accordance with the recommendations in the

owners manual(s).

5. Problems resulting from tampering, accident, abuse, negligence, unauthorized repairs or alternations, fire, flood,

lightning, freezing, external water, degradation of natural stone used in or immediately adjacent to a pool or spa,

war or acts of God.

DISCLAIMER.  THE EXPRESS LIMITED WARRANTIES ABOVE CONSTITUTE THE ENTIRE

WARRANTIES WITH RESPECT TO THE ABOVE-IDENTIFIED HAYWARD/GOLDLINE POOL

AUTOMATION AND CHLORINATION PRODUCTS AND IS IN LIEU OF ALL OTHER WARRAN-

TIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY OR FIT-

NESS FOR A PARTICULAR PURPOSE. THESE WARRANTIES GIVE YOU SPECIFIC LEGAL

RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS OF EQUIPMENT, LOST PROFITS OR

REVENUE, COSTS OF RENTING REPLACEMENTS, AND OTHER ADDITIONAL EXPENSES,

EVEN IF THE SELLER HAD BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME

STATES DO NOT ALLOW THE EXCLUSION OF LIMITATION OF INCIDENTAL OR CONSE-

QUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO

YOU.

NO WHOLESALER, AGENT, DEALER, CONTRACTOR OR OTHER PERSON IS AUTHORIZED

TO PROVIDE, SUPPLEMENT OR MODIFY ANY WARRANTY ON BEHALF OF HAYWARD/GOLD-

LINE.

THESE WARRANTIES ARE VOID IF THE PRODUCT HAS BEEN ALTERED IN ANY WAY AFTER

LEAVING THE FACTORY. FOR THE ABOVE-IDENTIFIED CHLORINATION PRODUCTS, THESE

WARRANTIES ALSO ARE VOID IF, DURING THE WARRANTY PERIOD, YOU USE A REPLACE-

MENT CHLORINATOR CELL OTHER THAN AN UNMODIFIED, NEW HAYWARD/GOLDLINE

CHLORINATOR CELL PURCHASED FROM HAYWARD/GOLDLINE. IF A WARRANTY BE-

COMES VOID, YOU STILL MAY PURCHASE SERVICE AND/OR TELEPHONE TECHNICAL

SUPPORT AT THE THEN CURRENT TIME AND MATERIAL RATES.

Содержание Pro Logic PL-P-4-CUL





































Отзывы: