Hayward Phantom Turbo 6000, Руководство пользователя

Страница: 32 / 46

7
Use Only Genuine Hayward Replacement Parts. Use Only Genuine Hayward Replacement Parts.
C Coon nn neeccttiin ng g tth hee P Ph haan nttoom m T Tu urrb boo C Clleeaan neerr T Too P Pooooll
6
IIn nssttaalllliin ng g U Un niivveerrssaall W Waallll FFiittttiin ng g
B Bu uiilld de errss:: Install the Dedicated Return Line at the
midpoint of the pool’s long wall.
S Sp pe ecciiffiicca attiio on n : Dedicated Return Line in Pool Wall.
D De ep ptth h::
At least 6 inches below water level.
S Siizze e:: 1-1/2 inch NPT Female Threaded.
1 1.. Flush plumbing lines before proceeding.
2 2..
Turn Booster Pump and Main Filtration Pump
O OF FF F
.
3 3.. Remove plug or existing Universal Wall Fitting from
previously installed pool cleaner (if any).
4 4.. Remove the Universal Wall Fitting (part O) and Teflon ® tape
from Bag #1.
5 5.. When installing or re-installing the Universal Wall Fitting
use Teflon
® tape on its plastic threads. Leave two starting
threads on the end of the Universal Wall Fitting un-taped.
6 6..
Screw the Universal Wall Fitting into the Dedicated
Return Line.
IIm mp po orrtta an ntt:: Turn the Universal Wall Fitting 1 full turn to the
right to engage starting threads. Be sure both parts are
started properly (not cross threaded) then resume tightening
– hand tighten only.
T Th he e U Un niivve errssa all W Wa allll F Fiittttiin ng g m ma ayy n no ott
ssccrre ew w a allll tth he e w wa ayy iin ntto o tth he e D De ed diicca atte ed d R Re ettu urrn n L Liin ne e..
D Do o n no ott o ovve err ttiig gh htte en n..
Teflon ® is a registered trademark of E.I. du Pont de Nemours
and Company.
A Asssseem mb blliin ng g aan nd d S Siizziin ng g tth hee R Riig giid d P Prreessssu urree H Hoossee
A Asssseem mb blliin ng g aan nd d S Siizziin ng g tth hee R Riig giid d P Prreessssu urree H Hoossee
1 1.. Open the plastic bag labeled #1 that contains 10 Rigid Hose
Pipes (Part N) and 5 Hose Pipe Couplings (Part
I ).
2 2.. Lubricate the 5 Hose Pipe Couplings by dunking them in
soapy water.
3 3.. Align the Barbs on the Hose Pipe Coupling with the Tabs on
the Rigid Hose Pipes and snap together. Be sure the black
o-ring does not slip out of the groove on the Hose Pipe
Coupling (if the o-ring is visible through the latch opening
when pipes are snapped together the o-ring has slipped out
of the groove and will leak)
4 4.. Make 5 S Se ettss of P Piip pe e A Asssse em mb blliie ess by connecting 1 Rigid
Hose Pipe onto each end of the Hose Pipe Couplings.
5 5.. Locate the “Measuring Tape” (packed in Bag #1), secure the
end of the tape marked “Wall Connector End” on the pool
coping immediately above the Universal Wall Fitting.
6 6.. Unroll the Measuring Tape, walk around the pool to the
farthest point along the pool wall from the Universal Wall
Fitting.
At the farthest point from the Universal Wall Fitting hold
the Measuring Tape at the pool edge/coping and read the
number of Pipe Assemblies specified on the tape.
U Un niivve errssa all W Wa allll F Fiittttiin ng g
R Riig giid d H Ho osse e P Piip pe e A Asssse em mb bllyy
Dedicated Return Line
Universal Wall Fitting (O)
M Me ea assu urriin ng g T Ta ap pe e
C Co on nn ne eccttiin ng g H Ho osse e P Piip pe ess
I
N
a. N No otte e:: If the measuring tape specifies more than 5 Pipe
Assemblies, you need to purchase the additional Pipe
sections (P/N AX6000HE) from your Authorized Hayward
Dealer.
b. If the measuring tape specifies fewer than 5 Pipe
Assemblies, set the remaining Pipe Assemblies aside these
will not be needed.
R Re ecctta an ng gu ulla arr--S Sh ha ap pe ed d P Po oo oll
K Kiid dn ne eyy--S Sh ha ap pe ed d P Po oo oll
A An ng glle e--S Sh ha ap pe ed d P Po oo oll
Universal Wall Fitting
(Dedicated Line)
Universal Wall Fitting
(Dedicated Line)
Farthest Point
Farthest Point
Universal Wall Fitting
(Dedicated Line)
Farthest Point
I N
1 Pipe
Assembly