Hayward AquaRite AQRS325OMNI Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 32

Hayward AquaRite AQRS325OMNI Скачать руководство пользователя страница 6

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

5

Front Panel Removal

DANGER of Death, Injury or Property Damage if procedure not followed.

Dead front removal

is required for this installation. Power to the AquaRite S3 panel MUST be shut off before the dead

front is removed. This means a complete shutdown of power to the entire AquaRite S3 panel.

Installation Steps

Details on each installation step are presented on the following pages:

1. Mounting the equipment (page 7)

AquaRite S3 main unit

Optional Temperature sensors

2. Plumbing (page 8)

TurboCell

Flow Switch

3. Electrical Wiring (page 9)

High Voltage

Low voltage wiring (Smart Relay, VSP, heater, sensors, heater, flow switch and TurboCell)

4. Prepare the pool water (page 17)

General Water Chemistry

Salt

5. System Startup (page 19)

Configuration

Operation

Remove

three screws

Pull the display away from

the panel by grasping it

with your hand (no tools

required). Then, remove

the 3 screws and pull the

plastic panel away from

the enclosure. It is not

necessary to disconnect

the display wiring.

«
...
4
5
6
7
8
...
»

Содержание AquaRite AQRS325OMNI

































Отзывы:

Нет отзывов