Hayter Power Trim 407C Скачать руководство пользователя страница 5

SAFETY RULES

5

F-050202L

18. Before each use, inspect the throttle

control lever and cable.  Make sure that

the cable is free and that the lever is not

damaged.  Also check the cable linkage

running to the carburetor for kinks, loose

fittings, and obstructions.  Verify that the

control bail is working properly.

19. Stop the rotating trimmer head when

crossing gravel drives, walks, or roads.

Wait for the cutting lines to stop rotating.

20. Watch for traffic when operating near, or

when crossing roads.

21. Stop the engine whenever you leave the

equipment, before cleaning repairing or

inspecting the unit, be sure the trimmer

head and all moving parts have stopped.

Let the engine cool, disconnect the

spark plug wire and move it away from

the spark plug.

22. If the equipment should start to vibrate

abnormally, stop the engine, disconnect

the spark plug wire and prevent it from

touching the spark plug.  Check immedi-

ately for the cause. Vibration is generally

a warning of trouble.

23. After striking a foreign object, stop the

engine. Remove the wire from the spark

plug. Inspect the machine for damage. If

damaged, repair before starting and op-

erating the machine.

24. Never leave the machine unattended

when the engine is running.   Remove

the wire from the spark plug.

25. Regularly inspect the machine.  Make

sure parts are not bent, damaged or

loose.

26. Never pick up or carry the machine while

the engine is running.

27. Prolonged exposure to noise and vibra-

tion from petrol engine powered equip-

ment should be avoided. Take

intermittant breaks and/or wear ear

protection from engine noise as well as

heavy work gloves to reduce vibration in

the hands.

II. Slope Operation

Slopes are a major factor related to slip and

fall accidents which can result in severe inju-

ry. All slopes require extra caution. If you feel

uneasy on a slope, do not trim it.

Do 

trim across the face of slopes; never up

and down. Do not trim excessively steep

slopes (maximum 15 degrees) or areas

where the ground is very rough. Exercise ex-

treme caution when changing direction on

slopes.

Do 

remove objects such as rocks, tree limbs,

etc.

Do 

watch for holes, ruts, or bumps. Tall grass

can hide obstacles.

Do not 

trim near drop-offs, ditches, or em-

bankments. The operator could lose footing

or balance.

Do not 

trim on wet grass. Reduced footing

could cause slipping.

III. Children

Tragic accidents can occur if the operator is

not alert to the presence of children. Children

are often attracted to the machine and the

trimming activity. 

Never 

assume that children

will remain where you last saw them.
1.

Keep children out of the trimming area

and under the watchful care of a respon-

sible adult.

2.

Be alert and turn machine off if children

enter the area.

3.

Before and while moving backwards,

look behind and down for small children.

4.

Never allow children to operate the ma-

chine.

5.

Use extra care when approaching blind

corners, shrubs, trees, or other objects

that may obscure vision.

IV. Service

1.

Use extra care in handling petrol and

other fuels. They are flammable and va-

pors are explosive.
a.

Use only an approved container.

b.

Never remove gas cap or add fuel

with the engine running. Allow en-

gine to cool before refueling. Do not

smoke.

c.

Never refuel the machine indoors.

d.

Never store the machine or fuel

container inside where there is an

open flame, such as a water heater.

e.

If the fuel tank has to be drained,

this should be done outdoors. The

drained fuel should be stored in a

container specifically designed for

fuel storage or it should be dis-

posed of carefully.

Содержание Power Trim 407C





























Отзывы: