manualshive.com logo in svg

Hayter Power Trim 407C, Руководство пользователя, Страница: 18 / 28

Поделиться
Скачать
Hayter Power Trim 407C Скачать руководство пользователя страница 18

MAINTENANCE

18

F-050202L

HOW TO 

REPLACE THE DRIVE BELT

To replace the drive belt, the trimmer head

and shield must be removed as follows.

WARNING: Before you remove

the drive belt, disconnect the

wire from the spark plug.

1. Remove the two fasteners that hold the

rear of the 

shield 

to the 

trimmer housing

(See Figure 15)

.

2. Remove the four fasteners that hold the

front of the 

shield 

and 

trimmer head 

to

the 

trimmer housing.

3. Remove the “V” pulley from the idler

bracket.

4. Raise the front of the 

trimmer housing

and remove the 

drive belt.

 On some mod-

els, it is necessary to loosen the 

mount-

ing bolt 

for the 

drive pulley 

to remove the

drive belt (see Figure 16). Do not bend the

belt guides.

NOTE: Make sure you replace the drive

belt only with a replacement belt from

the factory.

5. To assemble the 

drive belt

, reverse the

above steps. Make sure all fasteners are

tight. Make sure the 

mounting bolt 

for the

drive pulley 

is tight.

6. Check the routing of the 

drive belt.

 Make

sure the 

drive belt 

is inside of all 

belt

guides 

shown in Figure 16.

IMPORTANT: Test the drive system. Start

the engine and move the throttle control to

the FAST position. Engage and disengage

the trimmer head several times. When dis-

engaged, make sure the trimmer head com-

pletely stops when resting on the ground. If

the trimmer head continues to rotate, take

the machine to the nearest authorised

Service Dealer.

Figure 15

Trimmer Head

Shield

Drive Belt

Trimmer Housing

Figure 16

Belt Guide

Drive Belt

Belt Guide

Belt Guide

Mounting Bolt

Drive Pulley

“V” Pulley

Содержание Power Trim 407C





























Отзывы:

Нет отзывов