manualshive.com logo in svg

Hayter Power Trim 407C, Руководство пользователя, Страница: 15 / 28

Поделиться
Скачать
Hayter Power Trim 407C Скачать руководство пользователя страница 15

MAINTENANCE

15

F-050202L

LUBRICATION

How To Lubricate  

The Jackshaft Assembly

A 

grease fitting

 is provided to lubricate the

jackshaft assembly. Use a grease gun with au-

tomotive type grease to lubricate the jackshaft

assembly as shown in Figure 10.

Figure 10

Grease Fitting

How To Change Engine Oil

Change the engine oil when the engine is

warm. For the proper oil capacity, see “Product

Specifications”.
1. Disconnect spark plug wire from the spark

plug.

2. Remove the 

oil drain plug

 as shown in

Figure 11.

3. Drain all the engine oil into a flat pan.

4. Install the 

oil drain plug

. Make sure the

oil drain plug 

is tight.

5. Remove the

 

dipstick.

6. Fill the engine crankcase. 

DO NOT

OVERFILL

. For proper oil capacity, see

“Product Specifications”.

7. Connect the spark plug wire to the spark

plug.

Figure 11

Oil Drain Plug

HOW TO REPLACE THE AIR FILTER

Replace the air filter once a year or more often

in dusty or dirty conditions. 

DO NOT 

attempt to

clean or oil the air filter. Remove and install a

new air filter as follows:

CAUTION: Never run the engine without

the air filter installed. An air filter clogged

with dust can result in loss of engine power

and can cause excessive wear or damage

to the engine. If the air filter is clogged, re-

place immediately.

1. Disconnect the spark plug wire from the

spark plug.

2. Turn the 

cover 

clockwise as shown in

Figure 12. Remove the 

cover

 and the 

air

filter.

3. Discard the old 

air filter.

4. Clean the 

cover

 and the 

flange

.

5. Put the new 

air filter

 into the 

cover

.

6. Push the 

cover

 firmly against the 

flange.

Turn the 

cover

 counterclockwise until

tight. Be sure the retainers are locked

around the 

flange

.

7. Connect the spark plug wire to the spark

plug.

Figure 12

Cover

Air Filter

Flange

Содержание Power Trim 407C





























Отзывы:

Нет отзывов