background image

-2-

-3-

1

          

250 VAC 200mA Slow Blow Fuse 

             Fused power connection for circuit protection.

2

          

Lithium Battery

             On board clock back up.
             

CAUTION! DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY  

             REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT    
             TYPE RECOMMENDED BY THE MANUFACTURER. DISPOSE OF USED  
             BATTERIES ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS.

3

          Power Transformer

             Linear power supply for reliability and low noise.

4

          120 VAC Power Supply Terminals

             2-position Euro style pluggable connector for 120 VAC, 60Hz. Line to  
             neutral power connection.

5

          Auxiliary Input Status LED

             Indicates alarm condition for the auxiliary input.

6

          Membrane Switch Pin Connector

             Connection point for push button panel.

7

          Auxiliary Input Contacts

             Contact closure or pull-to-ground (10mA max.)

8

          Upstream RS232 Input Jack

             Connection point for Upstream RS232 network.

COMPONENT LOCATIONS

Figure 1

BACK

FRONT

  

9

          Upstream RS485 Connection Point

             5-position Euro style pluggable connector for upstream RS-485           
             network. 2 or 4-wire selectable.

10       

Downstream RS485 Connection Point

             5-position Euro style pluggable connector for downstream RS-485    
             network. 2 or 4-wire selectable.

11

        12 VDC Power Port

             Alternate 12 VDC connection point for use with plug in wall mount    
             transformer or power supply. (Auxiliary input is disabled if 12VDC    
             power is used)

12

        Membrane Switch Ribbon Cable

            

             

13

        Infrared Port

             Palm Pilot OS® communications port.

14

        Tri Color LED

             Green = Normal Operation. No network devices are in warning or alarm  
             mode.
             Yellow = Warning. One or more network devices are in warning mode.
             Red = Alarm. One or more network devices are in alarm mode or the  
             auxiliary input is active.

15       

Liquid Crystal Display

             High resolution LCD with adjustable backlight.

Содержание H8932












Отзывы: