MPS3004 / RS4004 AUDIO SYSTEMS
INSTALLATION GUIDE
HAWG WIRED
PAGE 7
NEWARK, CA
I
I
N
N
S
S
T
T
A
A
L
L
L
L
A
A
T
T
I
I
O
O
N
N
I
I
N
N
S
S
T
T
R
R
U
U
C
C
T
T
I
I
O
O
N
N
S
S
[
[
C
C
O
O
N
N
T
T
I
I
N
N
U
U
E
E
D
D
]
]
WIRING THE MAIN AMPLIFIER
(CONTINUED)
9.
DETERMINE AND CONNECT YOUR SOURCE UNIT OUTPUT TO THE AMPLIFIER INPUT CABLE(S)
USING ONE OF THE FOLLOWING HIGH OR LOW LEVEL INPUT METHODS:
9.1.
FACTORY SOURCE UNITS - HIGH LEVEL INPUT (NO RCA CONNECTORS AVAILABLE)
2 CHANNEL SOURCE, CONNECT THE FRONT SPEAKER OUTPUT WIRES FROM THE SOURCE
UNIT TO THE HIGH LEVEL INPUT CABLE (USE ATTACHED TERMINALS TO CONNECT INPUT
WIRES TO THE SPEAKER WIRE TERMINALS IF POSSIBLE).
4 CHANNEL SOURCE, CONNECT THE FRONT AND REAR SPEAKER WIRES FROM THE SOURCE
UNIT TO THE HIGH LEVEL INPUT CABLES RESPECTIVELY.
NOTE: FOR CUSTOM WIRING CONNECTIONS, WE RECOMMEND CRIMP, SOLDER, AND HEAT SHRINK.
HIGH LEVEL INPUT CABLE(S)
CONNECT
TOGETHER
H-D® SOURCE UNIT MODELS
2 CHANNEL – USE FRONT ONLY
4 CHANNEL – USE BOTH
1998-2005
8 OHM
1998-20XX
CVO
1
2006-20XX
2 OHM
FRONT LEFT +
WHT
f
f
e
e
WHT/ORG
(PIN 16)
WHT/ORG
(PIN 16)
WHT/ORG
(PIN 16)
FRONT LEFT –
BLK (WHT TWIST)
f
f
e
e
L.GRN/WHT
(PIN 17)
L.GRN/WHT
(PIN 17)
L.GRN/WHT
(PIN 17)
FRONT RIGHT +
RED
f
f
e
e
GRY/RED
(PIN 18)
GRY/RED
(PIN 18)
GRY/RED
(PIN 18)
FRONT RIGHT –
BLK (RED TWIST)
f
f
e
e
L.GRN/BLK
(PIN 1)
L.GRN/BLK
(PIN 1)
L.GRN/BLK
(PIN 1)
REAR LEFT +
WHT
f
f
e
e
BRN
(PIN 10)
BRN
(PIN 10)
BRN
(PIN 2)
REAR LEFT –
BLK (WHT TWIST)
f
f
e
e
WHT/BRN
(PIN 3)
WHT/BRN
(PIN 3)
WHT/BRN
(PIN 25)
REAR RIGHT +
RED
f
f
e
e
GRN
(PIN 11)
GRN
(PIN 11)
GRN
(PIN 1)
REAR RIGHT –
BLK (RED TWIST)
f
f
e
e
L.GRN/BRN
(PIN 4)
L.GRN/BRN
(PIN 4)
L.GRN/BRN
(PIN 24)
PIN NUMBERS APPLY TO H-D MAIN AND OVERLAY HARNESS CONNECTORS
NOTE
1
: CVO BIKES MAY BE EQUIPPED WITH A HIGH-OUTPUT SOURCE UNIT; DO NOT USE THE FOLLOWING WIRE
COLORS: WHT/PNK, PNK, WHT/GRY, GRY. THESE OUTPUTS CAN DAMAGE THE AMPLIFIER INPUTS.
9.2.
AFTERMARKET SOURCE UNITS - LOW LEVEL INPUT (RCA OUTPUT CONNECTORS AVAILABLE)
2 CHANNEL SOURCE, CONNECT THE FRONT RCA OUTPUT CONNECTORS FROM THE SOURCE
UNIT TO THE LOW LEVEL INPUT CABLE.
4 CHANNEL SOURCE, CONNECT THE FRONT AND REAR RCA OUTPUT CONNECTORS FROM
THE SOURCE UNIT TO THE LOW LEVEL INPUT CABLES RESPECTIVELY.
NOTE: VERY LITTLE DIELECTRIC GREASE IS NEEDED TO KEEP YOUR CONNECTIONS CORROSION FREE. VERY LITTLE
MOISTURE IS NEEDED TO CORRODE CONTACTS NOT COVERED WITH DIELECTRIC GREASE.
10.
PLUG THE CHOSEN INPUT CABLE(S) INTO THE CORRESPONDING CONNECTOR(S) OF THE MAIN
AMPLIFIER LABELED HIGH OR LOW, FRONT AND/OR REAR ACCORDINGLY.
