HAWEKA AXIS 500 Скачать руководство пользователя страница 19

Страница: 19 / 52

Wheel Alignment AXIS500

AXIS500 Manual Instructions

5 Front Wheel Alignment

5.1

Preparations

•

Carry out alignment on level ground.

•

Remove protective caps of wheel nuts or caps

respectively.

•

Clean rim between wheel nuts.

•

Check tire pressure and, if necessary, adjust as

specified.

Drive vehicle onto turning plates

•

Place turning plates centrally in front of the wheels.

•

Fasten turning plates with bolt to avoid torsion.

•

Drive vehicle on turning plates. The wheel centre

shall be positioned in the turning plate centre.

Mounting of laser measuring heads

(Illustration 1)

•

The magnetic feet of the 3-arm-star have to be

adjusted to the proper rim diameter. It is

recommended to fix the laser measuring head onto

a mounting stand of instrument cabinet

(Illustration

1).

•

Adjust magnetic cams by turning and shifting to

achieve all-over attachment of rim flange diameter

between wheel nuts.

•

Put the measuring heads with the magnets onto the

rim flange. Two magnets shall be placed above the

wheel centre and one below.

(Illustration 2).

Fitting of magnetic scales

•

Put the front wheels in the straight ahead position by

turning the steering wheel.

(Illustration 2)

•

Fix the first scale on the right-hand side of the

frame, if possible in the middle (regarding

lengthwise direction).

•

Switch on laser on the right-hand side.

(left hand drive vehicles, vice versa for RTA)

Pay attention to laser beam output
opening before switch on!

•

Turn right-hand laser until the laser point gets visible

on the magnetic scale.

•

Adjust scale with wing nut until the laser point

indicates

»0«.

•

Repeat the same procedure with the second scale

on the right-hand side. Now the magnetic scales

have the same length and must not be changed

again!

•

Attach one of the two scales on the left-hand

side, if possible in the same place

(Illustration 3)

Содержание AXIS 500





















































Результаты поиска

Содержание AXIS 500

Отзывы:

Бренды по названию

Популярные бренды

HAWEKA AXIS 500, Руководство по эксплуатации

Результаты поиска

Содержание AXIS 500

Отзывы:

Бренды по названию

Популярные бренды