background image

 

 

Page 3 
PBG

II

-9 

C.   BURNER CAPACITY TABLES 

300

500

750

1000

2000

3000

5000

(BTUx10

3

/hr)

310

520

750

1,030

2,040

3,000

5,040

(kW)

82

138

198

272

540

794

1,333

(scfh)

3,170

5,350

7,790

10,680

21,100

31,120

52,200

(nm

3

/hr)

85

143

209

286

565

834

1,398

(in.w.c.)

3.9

5.2

5.9

5.9

5.5

5.5

5.5

(mbar)

9.7

12.9

14.7

14.7

13.7

13.7

13.7

(in.w.c.)

3.2

4.5

4.1

4.3

3.5

4.5

3.1

(mbar)

8.0

11.2

10.2

10.7

8.7

11.2

7.7

(inches)

12

14

27

34

60

66

72

(mm)

305

356

686

864

1524

1676

1829

(inches)

3

5

6

8

12

16

16

(mm)

76

127

152

203

305

406

406

Flame Length

Flame Diameter

PBG BURNER

BURNER MODEL

SPECIFICATIONS                 

Capacity

Air Capacity

Body Air Pressure

Gas Inlet Pressure

 

Table 1. PBGII Burner Capacities 

NOTES:  

1. Capacities based on Natural Gas with HHV of 1,034 BTU/ft3 (Standard), and LHV of 
36.74 MJ/nm3 (Metric), 0.59 S.G., and a stoichiometric ratio of 9.74:1 with burner firing into 
chamber under no pressure at 10% excess air. 
2. Air and fuel flows based on STP operating conditions at sea level and industry standard 
air and gas piping practices. 
3. Gas Inlet Pressures supplied for natural gas.  Pressures are for reference only, not for 
burner setup. 
4. Flame lengths measured from end of burner tile. 
5. The above operating specifications are achievable by the burner. Not all control systems 
or components will produce these results. 
6. Consult gas manifold packages for expected performance. 
7. Packaged blower will produce the above pressures and flow at neutral conditions. 

 

300

500

750

1000

2000

3000

5000

(BTUx10

3

/hr)

350

570

810

1,110

2,220

3,260

5,480

(kW)

93

151

214

294

587

862

1,450

(BTUx10

3

/hr)

330

540

780

1,070

2,130

3,130

5,260

(kW)

87

143

206

283

563

828

1,391

(BTUx10

3

/hr)

320

530

770

1,050

2,090

3,070

5,150

(kW)

85

140

204

278

553

812

1,362

(BTUx10

3

/hr)

310

520

750

1,030

2,040

3,000

5,040

(kW)

82

138

198

272

540

794

1,333

(BTUx10

3

/hr)

300

510

730

1,010

1,990

2,930

4,920

(kW)

79

135

193

267

526

775

1,301

(BTUx10

3

/hr)

290

490

720

990

1,950

2,860

4,810

(kW)

77

130

190

262

516

757

1,272

+0.5"wc (1.2 mbar)

PBG BURNER

CAPACITY AT PRESSURE CONDITIONS

DUCT PRESSURE

-1.0"wc (2.5mbar)

-0.5"wc (1.2mbar)

-0.25"wc (0.6 mbar)

Neutral Chamber

+0.25"wc (0.6 mbar)

 

Table 2. Burner Capacities at Pressure Conditions 

 

      

 

Содержание PBGII 1000













Отзывы: