background image

OPERATION

Form No. SRM-0608

6

General

Use the following procedures to operate Serv-Rite™

Portable Shelves and Buffet Warmers.

Read all safety messages in the IMPORTANT

SAFETY INFORMATION section before operating

this equipment.
ELECTRIC SHOCK HAZARD: Do not fill SRB and

SRBW models with water. They are dry heat units

only, not steam table units.

Do not place anything on top of the glass sneeze

guard. It is not designed to be a weight-bearing

component.
Do not slide pans across glass surface, use

rough-bottomed pans, or drop anything on glass

surface. Scratching or breakage may occur.

Damage to glass surface or breakage of glass

caused by misuse is not covered under warranty.

Startup

1. Plug the unit into a properly grounded electrical

outlet of the correct voltage, size, and plug

configuration. See the SPECIFICATIONS section

for details.

2. Move the Power ON/OFF switch to the ON

position.

•The digital temperature controller will energize

and the current temperature of the heated

shelf will appear on the display.

WARNING

NOTICE

• The phrase “out 1” will appear in the upper left

corner of the display to show that the base is

in heat mode.

• For SRBW-1 and SRGBW-1 models; the

overhead heat lamps will turn on if the

LIGHTS control knob was left at a specific

setting the last time the unit was on.

BURN HAZARD: Some exterior surfaces on the

unit will get hot. Use caution when touching

these areas.

3. Press and release the SET key on the digital

temperature controller to verify the setpoint

temperature.

• The setpoint temperature will be shown for 15

seconds. After 15 seconds, the display will

revert to the current temperature of the heated

shelf. To change the setpoint temperature,

refer to “Changing the Setpoint Temperature”

in this section.

Figure 12. Digital Temperature Controller

Down Arrow

Key

Up Arrow

Key

“out 1”

Fahrenheit

Symbol

SET

Key

CAUTION

Model SRBW-1

Model SRG-1

Heated

Glass Shelf

Removable

Utensil Tray

Control

Panel

Glass

Sneeze

Guard

Overhead

Heat Lamps

Figure 11. Serv-Rite Components

Содержание Serv-Rite SRB-1

















Отзывы: