Hatco DL-400 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 20

background image

Form No. DHLM-1207

14

TROUBLESHOOTING GUIDE

SYMPTOM

PROBABLE CAUSE

CORRECTIVE ACTION

Heat is excessive.

Control switches burn-out
rapidly.

Unit mounted too close to
target area.

Check to see that installation is within
specifications for type/model. Increase
mounting height if too close.

Voltage supply too high.

Check power supply to unit, making sure
it matches rating on unit. If power supply
is incorrect, change to match rating.

Switches used are not Hatco
supplied.

Genuine Hatco components are specified
to operate safely and properly in the
environment in which they are used.
Replace switches with Genuine Hatco
Parts if switches are aftermarket or
generic.

«
...
14
15
16
17
18
...
»

Содержание DL-400





















Отзывы:

Нет отзывов

Похожие инструкции для DL-400

DHP-H Varius Pro+

Бренд: Danfoss Страницы: 12

Бренд: FAFCO Страницы: 14

Бренд: Dashan Страницы: 20

Бренд: Icom Страницы: 16

IC-FR4000 Series

Бренд: Icom Страницы: 20

Бренд: Olimpia splendid Страницы: 236

Бренд: veito Страницы: 40

Бренд: L.B. White Страницы: 18

Бренд: WMT Страницы: 7

Comfortstat 2 F 8ST

Бренд: GDC Страницы: 28

Flame-Max Vintage Oak Log Design

Бренд: Vanguard Страницы: 32

Бренд: Fenix Страницы: 12

Бренд: Saab Страницы: 40

Бренд: Hawking Страницы: 2

BASITRONIC CDX 11-U

Бренд: clage Страницы: 32

Flame Guard Safety System

Бренд: American Water Heater Страницы: 29

Aquantia KHPMS-BI Series

Бренд: Kaysun Страницы: 40

Бренд: Patron Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды