background image

42

Harsco Industrial, Patterson-Kelley Technical Service 1.877.728.5351

 

Gas Fired Boiler

 

 

5.5 Troubleshooting 

The NURO control will display graphical and/or text based error descriptions to announce any problems with 
the boiler.  There are two types of lockouts: manual reset lockouts which require the operator to physically 
press the on-screen or device’s reset button, and automatic reset lockouts which will self reset when the error 
condition clears.  For a comprehensive list of errors and potential resolutions, please refer to the NURO Advanced 
User’s Guide.

 

Should the unit fail to operate, call a qualified service technician to troubleshoot the problem and implement 
corrective actions.

 

5.5.1 Loss of Power

 

In the event of a power failure, the NURO touch screen  will go dark and the entire boiler will de-energize.  
The signal relays used to command auxiliary devices connected to the boiler (air dampers, pumps, etc.) will 
also lose power, so these devices will deactivate.  When power is restored, the sequence of operation will 
resume at 

Step 3 (

Section 5.4

)

.  If any error/lockout errors were present at the time of the power failure, the 

NURO control will retain that error/lockout when power is restored.

 

5.5.2 Loss of Water Level

 

The low water switch opens when there is an insufficient water level in the boiler. The NURO control will 
display 10010: 

“Low Water Limit”

, close the gas valve, and lock the boiler out.  When the water level is 

corrected and the on-screen reset button is pressed, the boiler will reset and resume the sequence of 
operation at 

 

Step 3 (

Section 5.4

5.5.3 Low Gas Pressure

 

The low gas pressure switch opens when there is (or has been) insufficient gas pressure available for proper 
operation of the boiler.  If an external gas-supply shut-off valve is closed for any reason, a low gas condition 
will result.  The NURO control will display 10012: 

“Low Gas Limit”

, close the gas valve, and lock the boiler 

out.  When proper gas pressure is restored, and the on-screen reset button is pressed, the boiler will reset 
and resume the sequence of operation at 

Step 3 (

Section 5.4

). 

5.5.4 High Gas Pressure

 

The high gas pressure switch opens when there is (or has been) excessive gas pressure for the proper 
operation of the boiler.  The NURO control will display 10011: 

“High Gas Limit”

, close the gas valve, and 

lock the boiler out.  When proper gas pressure is restored, and the on-screen reset button is pressed, the 
boiler will reset and resume the sequence of operation at 

Step 3

 (

Section 5.4

).

 

5.5.5 High Water Temperature

 

When the boiler water has exceeded both the operating temperature limit and the manual reset high-
temperature limit, the NURO control will display 10009: 

“High Temperature Limit”

, close the gas valve, and 

lock the boiler out.  When the water temperature falls below the high-limit temperature setting, the boiler will 
remain locked out until the water high-temperature limit switch is manually reset and the on-screen reset 
button is pressed.  Once reset, the control will resume the sequence of operation at 

Step 3

 (

Section 5.4

)

 

5.5.6 Low Air

 

If the NURO control displays either 65: 

“Interrupted Airflow Switch OFF”

 or 66: 

“Interrupted Airflow 

Switch ON”

this indicates improper airflow through the boiler.  First, verify proper standby blower operation – 

when the boiler is in “Standby”, the blower should also be in standby. 

Next, check for obstructions of the combustion air intake and/or exhaust (flue) piping.  Next, check the hoses 
leading to the air switches are not kinked or obstructed.  An error related to the air switch does not 
necessarily mean that the air switch is defective.

 

When 66: 

“Interrupted Airflow Switch ON”

 is displayed, check that the air switch is open when the blower 

is offline.  Ensure there is no air flow through the boiler when the blower is offline.  An excessive negative 
draft in the flue piping can cause air flow through the offline boiler which may be strong enough to maintain 
closure of the air switch.

 

Содержание SC-2000






































































Отзывы: