Harris Legacy 99-1300-0, Руководство по эксплуатации и техническому обслуживанию

Страница: 14 / 98

Revision B • 1/03
H A R R I S C O R P O R A T I O N
2-2
2 Installation
MAINFRAME CONFIGURATION
The Legacy design positions the input modules
in the physical center of the mainframe. This gives
the operator equal reach to peripheral equipment
located to the either side of the console.
Module Placement
The 14, 22, or 30 input module positions can
have any combination or order of the following
modules installed: Universal Input, Telco/Codec
(four maximum), and Remote Line Selector (RLS).
The remaining console positions are fixed. The Mic
Preamplifier module(s), Meter Switcher module,
Control Room module, optional Studio module,
and the two Output modules must be positioned
as shown in the illustration below.
Console Installation
To simplify console installation, logic cable wir-
ing diagrams for specific peripheral equipment are
available from the Harris Technical Services de-
partment. See page 4-1 for contact information.
INSTALLATION NOTE:
Do not locate the con-
sole near intense electromagnetic hum fields, such
as those produced by large power transformers
and by audio amplifiers that use inexpensive
power transformers operating in or near satura-
tion. Strong electromagnetic fields may impair the
performance of the Legacy and neighboring equip-
ment. Audio cables must also be routed to achieve
maximum practical distance from all AC power
mains wiring.
Reser
v
ed p
o
sition (c
o
v
ered by a 25" Blank panel)
Reser
v
ed p
o
sition (c
o
v
ered by a 25" Blank panel)
M
e
te
r Switcher
(standar
d
)
C
o
n
trol Ro
om (standard
)
S
tudio (optional) 25”
blank panel (standard
)
Legacy Mainframe, Module Configuration
M
ic P
reamp (standar
d
)
Output 1 (standard
)
Output 2 (standard
)
NOTE:
The number of input module positions matches the console model number (e.g., Legacy-22 has 22 input positions). There are
two DSP cards in the Legacy-14, three in the Legacy-22, and four in the Legacy-30.
The areas covered by the five 12.25" Blank Panels can be used for mounting Harris BMXdigital Accessory Panels or custom remote
control panels. Since the Harris BMXdigital Accessory Panels are 6" long, a PRE99-1100 Divider Kit (for mounting up to four
Accessory Panels in place of two 12.25" Blank Panels), or a PRE99-1101 Divider Kit (for mounting up to six Accessory Panels in place
of three 12.25" Blank Panels) is required. Typically, the PRE99-1100 Divider Kit is installed in place of the Blank Panels on the left
end of the console and the PRE99-1101 is installed in place of the Blank Panels on the right end of the console. 6" Blank Panels
(PRE99-1714-3) cover unused Accessory Panel positions.
Input modules
The input module positions are
filled with any combination or
number of Universal Input and
Remote Line Selector modules, and
up to four Telco/Codec modules.
Unused positions are covered with
25" Blank Panels.
12.25" Blank Panel (standar
d
)
12.25" Blank Panel (standar
d
)
12.25" Blank Panel (standar
d
)
12.25" Blank Panel (standar
d
)
12.25" Blank Panel (standar
d
)
DSP Card 1
(Master)
DSP Card 2 DSP Card 3* DSP Card 4*
* (number of DSPs present
set by the frame size)
M
ic Preamp 2 (optional)
12.5”
blank panel (standard
)
12.5” blank panel
(standard
)