background image

50

4.0

Operation

4.1

Introduction

DO NOT WALK UNDER A SUSPENDED LOAD

HOIST  OPERATORS  SHALL  BE  REQUIRED  TO  READ  THE  OPERATION  SECTION  OF  THIS  MANUAL,  THE 
WARNINGS  CONTAINED  IN  THIS  MANUAL,  INSTRUCTION  AND  WARNING  LABELS  ON  THE  HOIST  OR 
LIFTING  SYSTEM,  AND  THE  OPERATION  SECTIONS  OF  ANSI/ASME  B30.16  and  ANSI/ASME  B30.10.    THE 
OPERATOR  SHALL  ALSO  BE  REQUIRED  TO  BE  FAMILIAR  WITH  THE  HOIST  AND  HOIST  CONTROLS 
BEFORE BEING AUTHORIZED TO OPERATE THE HOIST OR LIFTING SYSTEM.

HOIST OPERATORS  SHOULD  BE  TRAINED  IN PROPER  RIGGING PROCEDURES FOR  THE  ATTACHMENT 
OF LOADS TO THE HOIST HOOK.

HOIST  OPERATORS  SHOULD  BE  TRAINED  TO  BE  AWARE  OF  POTENTIAL  MALFUNCTIONS  OF  THE 
EQUIPMENT THAT REQUIRE ADJUSTMENT OR REPAIR, AND TO BE INSTRUCTED TO STOP OPERATION IF 
SUCH  MALFUNCTIONS  OCCUR,  AND  TO  IMMEDIATELY  ADVISE  THEIR  SUPERVISOR  SO  CORRECTIVE 
ACTION CAN BE TAKEN.

HOIST  OPERATORS  SHOULD  HAVE  NORMAL  DEPTH  PERCEPTION,  FIELD  OF  VISION,  REACTION  TIME, 
MANUAL DEXTERITY, AND COORDINATION.

HOIST OPERATORS SHOULD 

NOT

HAVE A HISTORY OF OR BE PRONE TO SEIZURES, LOSS OF PHYSICAL 

CONTROL, PHYSICAL DEFECTS, OR EMOTIONAL INSTABILITY THAT COULD RESULT IN ACTIONS OF THE 
OPERATOR BEING A HAZARD TO THE OPERATOR OR TO OTHERS.

HOIST  OPERATORS  SHOULD 

NOT

OPERATE  A  HOIST  OR  LIFTING  SYSTEM  WHEN  UNDER  THE 

INFLUENCE OF ALCOHOL, DRUGS, OR MEDICATION.

OVERHEAD  HOISTS  ARE  INTENDED  ONLY  FOR  VERTICAL  LIFTING  SERVICE  OF  FREELY  SUSPENDED 
UNGUIDED LOADS.  DO 

NOT

USE HOIST FOR LOADS THAT ARE NOT LIFTED VERTICALLY, LOADS THAT 

ARE NOT FREELY SUSPENDED, OR LOADS THAT ARE GUIDED.

•   Read ANSI/ASME B30.16 and ANSI/ASME B30.10.
•   Read the hoist manufacturer’s Operating and Maintenance Instructions.
• Read all labels attached to equipment.

The operation of an overhead hoist involves more than activating the hoist’s controls.  Per the ANSI/ASME B30 
standards, the use of an overhead hoist is subject to certain hazards that cannot be mitigated by engineered features, 
but only by the exercise of intelligence, care, common sense, and experience in anticipating the effects and results of 
activating the hoist’s controls.  Use this guidance in conjunction with other warnings, cautions, and notices in this manual 
to govern the operation and use of your overhead hoist.

Содержание TF2 Series

















































































Отзывы: