background image

HSI #780-0867 

FireSpy Tracker

 Installation Manual 

 

 

19 

 

290-0159

NOTES

:

1)  Use only smoke detectors that are in the compatibility list in the 

owner's manual.

2) Leave end-of-line resistors on unused circuits.
3)  Combined load of all devices, including indicating appliances, is not to 

exceed 4A.

TYPICAL
STYLE Y

(CLASS B)

WIRING

USB

PORT

10K

LINE

NEU/LINE

EARTH

14 AWG MIN.

RJ31X

RJ31X

LINE INPUT

120VAC - 50/60Hz
240VAC - 50/60Hz

TO EXTERNAL
SERIAL MODULES

TYPICAL STYLE Z 

(CLASS A) 

WIRING

(end-of-line resistor 

not needed)

CONTACTS RATED

2A @ 30VDC

1.0 POWER FACTOR

USE ONLY POLARIZED

DEVICES ON NACs

Polarity shown is alarm condition

ALL NACs ARE REGULATED 24 DC

+

-

- +

RS485 RS485

B+

A+

A-

B-

B+

A+

A-

B-

NAC2

NAC3 /

AUX PWR

B+

A+

A-

B-

NC

COM

NO

NC

COM

NO

NC

COM

NO

-

+

+

-

RC

RELAYS

NAC1

RELA

Y1

RELA

Y2

AUX I/O

BA

TT

TROUBLE

TO INTERNAL

 SERIAL MODULES

A+

A-

B- B+

SLC

+

+

+

+

10K

USB

SECNDRY
PHONE

PRIMARY
PHONE

PDC

MB

J4

SW1

LEDs

FH1 FUSE: 7.5A MAX
CAUTION: For continued protection against risk of fire, 
replace only with same type and rating of fuse.

FH1

24VDC, .02A

10K

Marks non-supervised circuits
Marks non-power-limited circuits

All others are supervised and power limited.
Segregate power-limited wiring from
non-power-limited wiring by at least 1/4 inch.

SUPERVISED AND POWER LIMITED

S

P

S

P

P

P

P

P

P

TO RC

TO ANNUNCIATOR

ON CABINET DOOR

J4 jumpers present

TYPICAL STYLE 4 (CLASS B) WIRING

SLC B-

SLC B+

Example SLC wiring 

Example RJ31X wiring 

Isolators (optional) separate each zone

TYPICAL STYLE 6 (CLASS A) WIRING

ZONE 1

SLC A-

SLC A+

SLC B-

SLC B+

SLC A-

SLC A+

SLC B-

SLC B+

ZONE 2

Isolators separate each detector
Remove J4 jumpers

Remove J4 jumpers

TYPICAL STYLE 7 (CLASS A) WIRING

TIP

HOUSE RING

TIP

TELCO

RING

GRAY

BROWN

GREEN

RED

 

Figure 3-1: Wiring on MB 

 

Содержание FireSpy Tracker T1000

















































Отзывы: