Harmonic Ellipse 3000 Скачать руководство пользователя страница 315

Страница: 315 / 403

Chapter 11 DSNG Configuration

315

Ellipse 3000 Release 3.0, Rev. B

Common Modulation Parameters

11.4

Common Modulation Parameters

This group of parameters are common for both IF and L-Band modulator units.

The common modulation parameters are detailed in the following sub-paragraphs:

■

Modulation On/Off parameter, see

11.4.1 Modulation On/Off

■

Symbol Rate parameter, see

11.4.2 Symbol Rate

■

Spectrum Inversion parameter, see

11.4.3 Spectrum Inversion

■

Modulation Scheme parameter, see

11.4.4 Modulation Scheme

■

FEC and Modulation parameter, see

11.4.5 FEC and Modulation

■

Frame Length parameter, see

11.4.6 Frame Length

■

Operating Mode parameter, see

11.4.7 Operating Mode

■

Roll-Off Factor parameter, see

11.4.8 Roll-Off Factor

■

Pilot Mode parameter, see

11.4.9 Pilot Mode

11.4.1

Modulation On/Off

The Modulation on/off parameter sets the modulation mode of operation.

NOTE:

The Modulation on/off setting through the front panel is parallel supported using the [F2] shortcut key

on the touch-pad.

The available options are:

■

Off

– Modulation is disabled. Shortcut combination is

F2 + Down

■

– Modulation is enabled. Shortcut combination is

F2 + Left

The Modulation on/off default value is

Front Panel

To set the Modulation on/off parameter on the front panel:

❖

Navigate

Root > IF

L-Band Modulation > Modulation on/off

Web Manager

To set the Modulation on/off parameter in the Web Manager:

❖

Select

DSNG > MODULATOR AND UPCONVERTER

(see Figure 11–2 or Figure 11–3).

Modulation on/off

‚ Off

ƒ On

Содержание Ellipse 3000















































































































































































































































































































































































































Результаты поиска

Содержание Ellipse 3000

Отзывы:

Harmonic Ellipse 3000, Руководство пользователя, Страница: 315 / 403

Результаты поиска

Содержание Ellipse 3000

Отзывы: