Harmonic Ellipse 3000 Скачать руководство пользователя страница 321 | Manualshive

Страница: 321 / 403

background image

Chapter 11 DSNG Configuration

© 2013 Harmonic Inc. Harmonic All rights reserved.

321

Ellipse 3000 Release 3.0, Rev. B

Common Modulation Parameters

11.4.7

Operating Mode

The Operating Mode parameter sets the configuration and operation state for the Carrier and
Modulation Mode. Configuring the different Modulation and UpConverter parameters causes the
Carrier and Modulation Mode parameters to return to their default Off Value. Operating Mode
sets the reset mode of the Carrier and Modulation Mode.

The available options are:

■

C + M Auto Restore

– After changing other Modulation parameters, Carrier (C) and Modulation

(M) Mode are automatically restored to recently configured and saved values.

■

C + M Man Restore

– Carrier (C) and Modulation Mode (M) values are manually set. After

configuring other modulation parameters, Carrier and Modulation Mode are automatically set
to the default Off Value. The user must re-configure the values.

The Operating Mode default is

C and M Man Restore

.

Front Panel

To set the Operating Mode parameter on the front panel:

❖

Navigate

Root > IF

or

L-Band Modulation > Operating Mode

.

Web Manager

To set the Operating Mode parameter in the Web Manager:

❖

Select

DSNG > MODULATOR AND UPCONVERTER

(see Figure 11–2 or Figure 11–3).

Operating Mode

‚ C + M Auto Restore

ƒ C + M Man Restore

«
...
319
320
321
322
323
...
»

Содержание Ellipse 3000




















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Ellipse 3000

Бренд: Audiovox Страницы: 2

Бренд: TeVii Страницы: 23

Бренд: FLIR Страницы: 131

Бренд: BAICHUAN Страницы: 67

Бренд: Sound Devices Страницы: 97

Бренд: Sony Страницы: 10

DHG-HDD500 - Hi Definition Digital Video Recorder

Бренд: Sony Страницы: 1

Digital Betacam DVW-2000

Бренд: Sony Страницы: 8

Бренд: Sony Страницы: 14

Бренд: Sony Страницы: 160

Бренд: Sony Страницы: 168

Digital Betacam DVW-2000

Бренд: Sony Страницы: 164

DSR 45A - Professional Editing Video Cassete recorder/player

Бренд: Sony Страницы: 220

Бренд: Sony Страницы: 208

Бренд: Sony Страницы: 234

Бренд: Sony Страницы: 506

Бренд: Kamera2000 Страницы: 9

Бренд: Whistler Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды