Harmonic Ellipse 3000 Скачать руководство пользователя страница 320

Страница: 320 / 403

Chapter 11 DSNG Configuration

320

Ellipse 3000 Release 3.0, Rev. B

Common Modulation Parameters

11.4.6

Frame Length

The Frame Length parameter sets the DVB-S2 modulation frame length.

NOTE:

This parameter is only relevant for units operating under DVB-S2 modulation scheme.

This parameter is not available in the DVB-S module (default value is 32 Kbits).

This is a dynamic value screen and displays various available values according to the selected
modulation scheme. The available options are:

The selected value sets the frame length to the selected number in bits (for example, selecting
64,800 sets the frame length to 64,800 bits.

Front Panel

To set the Frame Length parameter on the front panel:

❖

Navigate

Root > IF

L-Band Modulation > Frame Length

Web Manager

To set the Frame Length parameter in the Web Manager:

❖

Select

DSNG > MODULATOR AND UPCONVERTER

(see Figure 11–2 or Figure 11–3).

Modulation Scheme

Available Values

DVB-S

32,000 bits

DVB-S2

16,200 bits (used for Low latency mode)
64,800 bits

Frame Length

‚ 16200 bits

ƒ 32800 bits

‚ 64000 bits

Содержание Ellipse 3000















































































































































































































































































































































































































Результаты поиска

Содержание Ellipse 3000

Отзывы:

Harmonic Ellipse 3000, Руководство пользователя, Страница: 320 / 403

Результаты поиска

Содержание Ellipse 3000

Отзывы: