Harman Martin MAC Aura PXL Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 46

background image

16

MAC Aura PXL User Guide

• all the settings in the PERSONALITY menu,

• the fixture’s DMX address, and

• the fixture’s DMX control mode: Compact, Basic, Extended or Ludicrous.

Fixture information readouts

The following fixture information can be called up in the display:

•

POWER ON TIME

provides two counters:

- The

TOTAL

counter is not user-resettable and displays total hours powered on since manufacture.

- The

RESETTABLE

counter is user-resettable and displays the number of hours the fixture has been

powered on since the counter was last reset.

•

POWER ON CYCLES

also provides two counters:

- The

TOTAL

counter is not user-resettable and displays the total number of power on/off cycles since

manufacture.

- The

RESETTABLE

counter is user-resettable and displays the number of power on/off cycles since the

counter was last reset.

•

SW VERSION

displays the currently installed firmware (fixture software) version.

•

RDM UID

displays the fixture’s factory-set unique ID for identification in RDM systems.

•

FAN SPEEDS

provides separate status readouts from the fixture’s cooling fans.

•

TEMPERATURES

provides separate PCB temperature readouts. You can choose to see the current

readout or the minimum and maximum temperature levels since the fixture was last powered on.

DMX signal monitoring

The MAC Aura PXL provides data on the DMX signal it is receiving in the

DMX LIVE

menu. This information

can be useful for troubleshooting control problems.

•

RATE

displays the DMX refresh rate in packets per second. Values lower than 10 or higher than 44 may

result in erratic performance, especially when using tracking control.

•

QUALITY

displays the quality of the received DMX data as a percentage of usable packets from the data

received. Values much below 100 indicate interference, poor connections, or other problems with the
serial data link that are the most common cause of control problems.

•

START CODE

displays the DMX start code. Packets with a start code other than 0 may cause irregular

performance.

The remaining options under

DMX LIVE

display the DMX values in a range from 0 - 255 that are being

received on each channel. The DMX channels displayed depend on whether the fixture is in Compact,
Basic, Extended or Ludicrous DMX mode.

Test sequences

The

TEST

menu lets you test all the fixture’s effects, test LED effects only, test mechanical effects only or

test pan and tilt only. If you are going to run a test, be prepared for the head to move without warning and be
prepared for the fixture to light up suddenly.

To run a test:

• In the TEST menu, scroll to TEST ALL, TEST LEDS, TEST EFFECTS or TEST PAN/TILT and press

Enter.

• Scroll to the item you want to test and press Enter to start a test sequence for that item.

• Press Menu to stop the test sequence.

«
...
14
15
16
17
18
...
»

Содержание Martin MAC Aura PXL















































Отзывы:

Нет отзывов

Похожие инструкции для Martin MAC Aura PXL

Бренд: Raymarine Страницы: 464

Бренд: 3M Страницы: 8

Бренд: ZOLL Страницы: 3

Бренд: Landoll Страницы: 34

Бренд: OMCA Страницы: 36

Бренд: Salford Страницы: 64

Бренд: PANDROL Страницы: 36

Бренд: e+p Elektrik Handels Страницы: 2

Бренд: Maico Страницы: 55

Бренд: Maico Страницы: 38

Бренд: Maico Страницы: 2

Бренд: MAHA Maschinenbau Haldenwang Страницы: 13

Бренд: Velp Scientifica Страницы: 16

Бренд: Velp Scientifica Страницы: 2

Бренд: Velp Scientifica Страницы: 32

Бренд: Velleman-Kit Страницы: 32

Бренд: Hach Страницы: 456

Бренд: GE Страницы: 176

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды