Harman Martin MAC Aura PXL Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 46

background image

10

MAC Aura PXL User Guide

The status LED is only active when the display is active. If the display enters sleep mode, the LED will also
sleep.

Battery power

The MAC Aura PXL’s onboard battery gives access to the most important functions in the control panel
when the fixture is not connected to AC power. The following functions are available on battery power:

• DMX address

• DMX control mode (Compact/Basic/Extended/Ludicrous)

• Fixture ID

• All personality settings (pan/tilt, cooling, fan clean mode, dimming curve, DMX reset, parameter shortcuts,

all display settings, error mode)

• Default settings

• Information (Power On Hours and Power Cycles counters, Software version)

• Error list

To activate the display when the fixture is not connected to power, press the Menu button

C

. Press again to

enter the menus. The display extinguishes after 10 seconds with no user input and the control panel is
de-activated after 1 minute with no user input. Press the Menu button

C

again to re-activate.

Shortcuts

If you hold the Menu button

C

pressed in for 2 - 3 seconds, a shortcut menu with the most important

commands appears. Select a command with the Up and Down buttons

D

and press the Enter button

E

to

activate, or press the Menu button

C

again to cancel.

•

RESET ALL

resets the whole fixture

•

ROTATE DISPLAY

rotates the MAC Aura PXL display 180°.

Settings stored permanently

The following settings are stored permanently in the fixture memory and are not affected by powering the
MAC Aura PXL off and on or by updating the fixture software:

• DMX address

• DMX control mode (Compact/Basic/Extended/Ludicrous)

• Fixture ID

• All personality settings (pan/tilt, cooling, dimming curve, DMX reset, parameter shortcuts, all display

settings, error mode, etc.)

• Resettable counters

• Service settings (adjustment, calibration)

These settings can be returned to factory defaults using the control menus or via DMX.

Service mode

Holding the Menu and Enter buttons

C

and

E

both pressed in while powering the fixture on puts the fixture

into service mode, in which pan and tilt are disabled and a

SERV

warning appears in the display. Service

mode removes the risk of unexpected head movement during service adjustments.

Cycling power and allowing the fixture to start normally takes it out of service mode.

«
...
8
9
10
11
12
...
»

Содержание Martin MAC Aura PXL















































Отзывы:

Нет отзывов

Похожие инструкции для Martin MAC Aura PXL

Бренд: Bante Instruments Страницы: 6

Бренд: Hantek Страницы: 124

Бренд: Hameg Страницы: 10

Бренд: HANYOUNG NUX Страницы: 2

Бренд: Nellcor Страницы: 161

OXIMAX N-600X Series

Бренд: Nellcor Страницы: 210

Бренд: Oase Страницы: 120

Бренд: OAKWORKS Страницы: 24

Бренд: Öhlins Страницы: 8

Бренд: &Tradition Страницы: 3

Flowerpot VP3 Verner Panton 1968

Бренд: &Tradition Страницы: 3

Бренд: ?HC Страницы: 2

FLOWERPOT GARDEN VP5

Бренд: &Tradition Страницы: 4

FLOWERPOT GARDEN VP3

Бренд: &Tradition Страницы: 4

Бренд: &Tradition Страницы: 4

Бренд: Nady Audio Страницы: 2

Serious Steel 805106

Бренд: ParaBody Страницы: 6

Z33-D060.02 S2A

Бренд: Jäger Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды