background image

 8

3.0 Rear Panel

1.  Power Supply Input

Connect the included JBL power supply here. 

2.  Firmware Update

The USB connector allows you to connect your computer to the mixer for updating the firmware. 

To retrieve the firmware version of your mixer, observe the LEDs on the rear panel while the mixer 

boots. The LED in the SOURCE 1 section represents major. The LED in the SOURCE 2 section 

represents minor. The LED in the SOURCE 3 section represents build. The LED beside the MIC 

connector represents revision. Each LED will flash green a number of times for the numeral it stands 

for. The format is “major.minor[.build[.revision]]”. For example, if the first released version is “v1.0.0.0”, 

when you switch the mixer on, the LED in the SOURCE 1 section will flash green once, and the 

remaining LEDs will turn red. The unit is then ready for use.

3.  Crossover

This switch activates the crossover feature for the left, right, and subwoofer ZONE outputs. When the 

crossover switch is “in”, the left and right outputs will allow frequencies above 125Hz to pass and the 

subwoofer output will allow frequencies below 125 Hz to pass. When the crossover is switch is “out”, 

the left, right, and subwoofer outputs will pass full-range audio to allow the end-user to utilize the built-

in crossover functionality on their speakers, if desired. Use this crossover feature if the bass response 

of your room is too boomy when you are using inexpensive loudspeaker transformers or in conjunction 

with the subwoofer crossover (see subwoofer crossover section).

4.  Zone Output(s)

The mixer ZONE outputs utilize balanced Euroblock connectors. These outputs carry the Left, Right, 

and Subwoofer signals. Connect these outputs to your power amplifier(s).

5.  AutoWarmth™ Indicator and Trim Pot

These indicators flash green when the AutoWarmth function is triggered. This trim pot adjusts the point 

at which the signal level must drop to before AutoWarmth™ will kick in (referred to as threshold).

CSM-32 illustration

CSM-21 illustration

1

2

4

9

3

5

6

10

13

14

11

12

8

15

1

2

4

9

7

8

3

5

6

10

13

14

15

11

12

Содержание JBL CS Commercial Solution Series

























Отзывы: