22
maintenance
Inspect the hopper lid sponge gasket. It is important to
maintain a good hopper lid seal.
Do not allow pellets or sawdust to remain on
the hopper lip after filling.
Control door
finger hole
Draft Meter hex plug
Glass Gasket
Replace glass
only with high
temperature
ceramic glass.
Inspect door gasket during cleaning
and inspection
Fig. 34
Soot and Flyash: Formation and Need for
removal- The products of combustion will contain
small particles of flyash. The flyash will collect in
the exhaust venting system and restrict the flow
of flue gases. Incomplete combustion, such as
occurs during start-up, shut-down, or incorrect
operation of the room heater will lead to some soot
formation which will collect in the exhaust venting
system. The exhaust venting system should be
inspected at least once every year to determine if
cleaning is necessary.
Most retailers offer a cleaning service for their
customers. The best time to have this cleaning
performed is after the heating
season.
If You Experience a Soot or
Creosote Fire;
Turn the mode
slector dial to the "OFF" position.
Allow the unit to shut-down.
do
NOT disconnect the power to
the appliance. do NOT open the
appliance door or hopper lid.
Contact your dealer to have the unit
professionally inspected and cleaned
prior to use.
Creosote - Formation and Need for removal -
When wood is burned slowly, it produces tar and other
organic vapors, which combine with expelled moisture
to form creosote. The creosote vapors condense in the
relatively cool chimney flue of a slow-burning fire. As a
result, creosote residue accumulates on the flue lining.
When ignited, this creosote makes an extremely hot
fire. The pellet vent pipe should be inspected at least
twice monthly during the heating season to determine
if a creosote buildup has occurred. If creosote has
accumulated (3mm or more) it should be removed to
reduce the risk of a chimney fire.
Guidance on minimizing creosote formation and
the need for periodic creosote removal
: The chimney
should be inspected periodically during the heating
season to determine if a creosote build-up has occurred.
If a significant layer of creosote has accumulated, 1/8”
(3mm) or more, it should be removed to reduce the risk
of a chimney fire.
The glass used in your stove is manufactured to exact
standards to withstand the high heat of the fire, but like
all glass, it must be treated with common sense and
care. Never abuse the glass by slamming the door shut
or striking the glass with a heavy object. If the glass is
broken or damaged, do not operate the stove until it
has been replaced.
glass - replacement
Remove pieces carefully. Replace glass only with
Harman replacement arched glass Part #3-40-247127
12.25"X10"X0.188" (311mmX254mmX5mm) ceramic;
do Not use Substitutes.
Carefully remove damaged glass, gasket material,
and hold down clips (set aside).
Install the self adhesive 1/4"” gasket material around
the front face of the glass. Set the glass panel and
gasket gently onto the door. Install the hold down clips
and tighten with bolts.
glass - Cleaning
Sometimes it will be necessary to clean accumulated
ash from the glass surface; allowing this ash to remain
on the glass for long periods can result in “etching” due
to the acidity of the ash. Never clean the glass while it
is hot, and
do not
use abrasive substances. Wash the
surface with cool water, and rinse thoroughly. You may
wish to use a non-abrasive cleaner specifically designed
for use on stove glass. In any case, dry thoroughly
before relighting your stove.
Содержание Accentra
Страница 2: ......
Страница 41: ...41 Service Maintenance Log Date Of Service Performed By Description Of Service ...
Страница 42: ...42 Service Maintenance Log Date Of Service Performed By Description Of Service ...
Страница 43: ......
