Harman Kardon DPR 1001 Скачать руководство пользователя страница 31

Страница: 31 / 44

MULTIROOM OPERATION 31

MULTIROOM OPERATION

To change the length of time that the semi-OSD dis-
plays remain on the screen, go to the

ADVANCED

menu as outlined earlier, and press the

⁄

Navigation Buttons

as needed, until the

SEMI OSD TIME OUT

line is highlighted

in reverse video. Next, press the

‹

›

Navigation

Buttons

until the desired time in seconds is dis-

played. Unlike most of the other options in this menu,
this is a permanent setting change, and the time-out
entry will remain in effect until it is changed, even
when the unit is turned off.

If you wish to make other adjustments, press the

⁄

Navigation Buttons

until the desired set-

ting is highlighted in reverse video, or highlight the

RETURN TO MAIN MENU

line and then

press the

Set Button

to select another menu for

adjustment. If no further adjustments are required,
press the

OSD Button

to exit the menu system.

Full-OSD Time-Out Adjustment

The

FULL OSD

menu system is used to simplify

the setup and adjustment of the DPR 1001, using a
series of on-screen menus. The factory default setting
for these menus leaves them on the screen for 20
seconds after a period of inactivity before they disap-
pear from the screen (Time-Out). Time-Out is a safety
measure to prevent image retention of the menu text
in your monitor or projector, which might happen if it
were left on indefinitely. However, some viewers may
prefer a slightly longer or shorter period before the
Time Out display.

To change the Full-OSD Time-Out, you will need to
make an adjustment in the

ADVANCED

(Figure 13). To start the adjustment, press the

OSD

Button

to bring the

MAIN

menu to the

screen. Press the

Navigation Button

, until

the

ADVANCED

line is highlighted in reverse

video. Press the

Set Button

to enter the

ADVANCED

menu (Figure 13).

At the

ADVANCED

menu (Figure 13) make

certain that the

FULL OSD TIME OUT

line

is highlighted in reverse video by pressing the

⁄

Navigation Buttons

as needed. Next, press the

‹

›

Navigation Buttons

until the desired time

is displayed in seconds. Unlike most of the other
options in this menu, this is a permanent setting
change, and the Time-Out entry will remain in effect
until it is changed, even if the unit is turned off.

If you wish to make other adjustments, press the

⁄

Navigation Buttons

until the desired set-

ting is highlighted in reverse video, or highlight the

RETURN TO MAIN MENU

line and then

press the

Set Button

to select another menu for

adjustment. If no further adjustments are required,
press the

OSD Button

to exit the menu system.

Multiroom Operation

The DPR 1001 is fully equipped to operate as the
control center for a multiroom system with optional
remote external infrared (IR) sensors, speakers and
power amplifiers. Although some multiroom installations
will require the services of a specially trained installer, it is
possible for the average do-it-yourself hobbyist to install
a simple remote room system.

Installation

The key to remote room operation is to link the remote
room to the DPR 1001’s location with wire for an
infrared link and speakers or an amplifier. For installation
instructions for Multiroom use, see page 15.

Multiroom Setup

Once the audio and IR link connections have been
made, the DPR 1001 needs to be configured for multi-
room operation using the steps below. Press the

OSD

Button

to bring the

MAIN

menu (Figure 1)

to the screen. Press the

Navigation Button

until the

MULTI-ROOM

line is highlighted. Press

the

Set Button

to enter the

MULTI-ROOM

menu (Figure 14).

Figure 14

When the

MULTI-ROOM

menu appears, the

MULTI-ROOM

line will be highlighted. Since this

line is used to turn the system on and off, do not make
an adjustment here unless you wish to turn the system
on at this time. To turn the system on, press the

›

Navigation Button

so that

appears. If you do

not wish to turn the system on at this time or to proceed
to the next step, press the

Navigation Button

so that the

MULTI IN

line is highlighted.

At the

MULTI IN

line, press the

‹

›

Navigation

Buttons

until the desired input to the multiroom

system appears. When the selection has been made,
press the

Navigation Button

once so that the

MULTI VOL

line is highlighted.

At the

MULTI VOL

line, press the

‹

›

Navigation Buttons

until the desired volume level

for the multiroom system is entered. DO NOT use the
regular volume control knobs for this setting. When all

settings for the multiroom setup have been made,
press the

⁄

Navigation Buttons

until the

RETURN TO MAIN MENU

line is highlighted.

If you have no other adjustments to make, press the

OSD Button

to exit the menu system.

Multiroom Amplifier Configuration

Since the DPR 1001 is equipped with seven channels
of amplification, they may be allocated to either full 7.1
channel operation, or they may alternatively be used to
power speakers that are fed the output of the multiroom
system. Thus, when only 5.1 channels are required for
the main listening room, you may power speakers in a
second zone without the need for additional external
amplifiers. This is a major improvement over the use of
simple “Speaker A/B” switches, as it allows for a fully
separate source and independent volume levels at the
remote location.

To configure the DPR so that the amplifiers normally
used for the Surround Back channels are used for the
multiroom system, you must make an adjustment in the

ADVANCED

menu (Figure 13). To start the adjust-

ment, press the

OSD Button

to bring the

MAIN

menu to the screen. Next, press the

Navigation Button

until the

ADVANCED

line

is highlighted in reverse video. Press the

Set Button

to enter the

ADVANCED

menu.

When the

ADVANCED

menu is on the screen, the

SB AMPS

item at the top of the menu list will be

highlighted in reverse video. Press the

‹

›

Navigation

Buttons

so that the right side of the menu line

changes to

MULTI ROOM

When this configuration adjustment is complete, press
the

⁄

Navigation Buttons

until

RETURN

TO MAIN MENU

is highlighted in reverse video

and press the

Set Button

to select another menu

for adjustment. If no further adjustments are required,
press the

OSD Button

to exit the menu system.

IMPORTANT NOTE:

Once the amplifiers are configured

as shown above so that the multiroom outputs are pow-
ered by the DPR’s internal amplifier, the speaker configu-
ration will automatically be reset for 5.1 channel opera-
tion in the main room. This means that 6.1/7.1-channel
operation will not be possible until the setting shown
above is returned to OFF. For that reason, use of the
internal amplifier for multiroom operation is recommended
only if your main listening room uses a 5.1 speaker
system. If the main room has a 6.1 or 7.1 speaker
setup, it will be necessary to use an optional, external
power amplifier to power the speakers used in the
multiroom system.