background image

WARRANTY OF 

HARMAN-KARDON CITATION KITS

 

For  a  period  of  90  days  following  the  original  date  of  purchase,  all  parts  supplied  with  Harman-Kardon 

Citation Kits are guaranteed by the manufacturer to be free from defects in material and workmanship when put 
to normal use and service. This guaranty is specifically limited to the following conditions: 

 

(

1

)

  To validate the warranty, the warranty card accompanying each kit must be filled out completely and 

returned to the factory immediately following the date of purchase. 

 

(

2

)

  Harman-Kardon  reserves  the  right  to  substitute  replacement  parts  for  any  which  may  be  found  de-

fective. 

 

(

3

)

  The warranty is effective only as to parts which are defective at the time of sale or become defective as 

the result of the normal operation during the 90 day period following the date of sale. 

 

(

4

)

  This warranty is limited to those parts which are returned to the factory transportation prepaid, and in 

the judgment of Harman-Kardon are found defective under the terms of this warranty. 

 

(

5

)

  This warranty is specifically void as to any parts in which 

acid core solder or paste fluxes 

have been used. 

This warranty is in lieu of all other warranties, express or implied, and of all other obligations on the part of 

Harman-Kardon. Harman-Kardon neither assumes nor authorizes anyone else to assume for it any other liability 
in connection with the sale of this kit. 

Harman-Kardon  does  not  assume  liability for  damages  or  injuries incurred  during  the  construction  of  this 

kit. 

SERVICE POLICY 

If you should have difficulty with this kit and cannot resolve the problem through your own efforts, write 

directly to us for advice. Harman-Kardon has established a special Citation service division to answer all ques-
tions pertinent to the assembly, testing or installation of this instrument. Address all correspondence to: 

If the factory feels your difficulty may not be easily resolved through your own efforts, you will be notified 

of the authorized warranty service station nearest your home. These stations are a t your disposal in the event you 
require  assistance.  However,  please  note  they  will  not  accept  a  unit  unless  previous  factory  authorization  has 
been given. 

If it is necessary to ship your set, pack the unit carefully and return to the warranty station designated by the 

factory via Railway Express, PREPAID. Pack the kit in a large, rugged container using a substantial quantity of 
padding and bracing. Attach a tag to the set indicating your name, address and the specific problem. Mentioning 
the other components in your installation may be of value. 

The Harman-Kardon warranty station will inspect and service your kit at a minimum service charge of $10 

plus the cost of parts or tubes that are out of warranty, provided the unit has been constructed and completed  in 
accordance with the instructions in this manual. 

This special repair offer is available to you for the life of the instrument. 

PLEASE NOTE THIS SERVICE APPLIES ONLY TO FULLY COMPLETED INSTRUMENTS. 

INCOMPLETE  AMPLIFIERS  OR  THOSE  THAT  HAVE  BEEN  MODIFIED  IN  DESIGN  WILL 
NOT BE ACCEPTED. AMPLIFIERS SHOWING EVIDENCE OF ACID CORE SOLDER OR PASTE 
FLUX WILL SIMILARLY BE REFUSED. 

HARMAN-KARDON, INC. 

Citation Kit Division

 

PLAINVIEW, L. I., NEW YORK 

Содержание Citation II









































Отзывы: