Harman Kardon AVR 500 Скачать руководство пользователя

Страница: 27 / 40

MULTIROOM OPERATION

Multiroom Operation

The AVR500 is fully equipped to operate
as the control center for a sophisticated multi-
room operation with optional remote external
InfraRed (IR) sensors, speakers and power
amplifiers. Although some multi- room installa-
tions will require the services of a specially
trained installer, it is possible for the average
do-it-yourself hobbyist to install a simple
remote room system.

Installation

The key to remote room operation is to link the
remote room to the AVR500’s location with
wire for an infrared receiver and speakers or an
amplifier. For complete installation instructions
for Multiroom use, see page 14.

Multiroom Setup

Once the audio and IR link connections have
been made, the AVR500 needs to be configured
for multiroom operation using the steps below.
When making these selections, you may use the
front-panel Information Display, or use the On-
Screen Display System. Either the Semi-OSD sys-
tem may be used, in which case the choices will
appear as a single-line display at the bottom of
the screen, or the full-screen display may be used.
When the Full-OSD display system is in use, the
complete list of choices will appear on the screen.

To activate the Semi-OSD, press the

OSD

button

once. To activate the Full-OSD, press the

OSD

button

three times. This will turn the

Semi-OSD on and then off. The Full-OSD will
appear after the third button press.

Once you have determined which, if any, OSD
system to use, setup and operation of the multi-
room system is simple.

1. Press the

Multi

button

to initiate the

multiroom system. If the Semi-OSD system is
engaged, a message will appear at the bot-
tom of the screen. If the Full-OSD system is
engaged, the complete multiroom menu
(Figure 9) will be shown on the video display.
Press the

Set

button

within twenty

seconds to enter the multiroom menus.

Figure 9

2. Press the

⁄

buttons

to turn the

multiroom system on or off, as indicated by
the front-panel Information Display message,
the Semi-OSD message, or the change in the
highlighted video in the Full-OSD screen. Press
the

Set

button

to enter the settings.

3. Press the

Button

to move to the input

settings. Press the

Set

button

to change

the input source. Press the

⁄

buttons

to select the desired input. When the

input source you wish to send to the remote
room location appears on the front-panel
Information Display, in the lower screen Semi-
OSD message, or is highlighted in reverse
video in the Full-OSD listing, press the

Set

button

to enter the selection.

4. Press the

Button

to move to the

multilevel setting. Press the

Set

button

if you wish to change the output level.
Within twenty seconds, press the

⁄

buttons

to change the output level for

the multiroom feed. The volume change will
appear as a number in dB increments below
the 0dB reference level in the front-panel
Information Display, as a lower third Semi-
OSD message, or as the last line in the
Full-OSD status display.

5. Press the

Set

button

to enter the set-

ting. If no further buttons are pressed within
five seconds, the unit will return to normal
operation.

Multiroom Operation

To activate the feed to the remote room, press
the

Multi

button

on the remote. Next,

press the

Set

button

. Press the

⁄

but-

tons

to turn the multiroom feed on or off.

When the multiroom system is on, the

MULTI

indicator

will light in the

Information

Display

, and the

Main Information

Display

or OSD will display

MUL

ROOM ON

. Press the

Set

button

enter the setting.

When the multiroom system is turned on, the
previously selected input will be fed to the

Multi

Out

jacks

•

on the rear panel. The volume will

be as set in the previous selection, although it
may also be adjusted using an optional volume
control in the remote location or on the optional
audio power amplifier connected to the

Multi

Out

jacks

•

If an optional IR sensor is located in the remote
room and connected to the AVR500’s Multi IR
jack

, the multiroom system may be turned

on or controlled by simply pointing the AVR500
remote, or an optional programmable remote
that includes codes for the AVR500, at the IR
sensor. Note that depending on the type of pro-
grammable remote used, the code for the AVR’s
Multi button may not be contained in the
preprogrammed code library, and must be
“learned” into the remote, if possible.

To change the input source for the multiroom
feed once it has been turned on, follow the
instructions on this page.

Once the multiroom system is turned on, it will
remain on even if the AVR500 is placed in the
Standby mode in the main room by pressing
the

Power Off Button

or the

System

Power Control

on the front panel. To turn

off the multiroom sysytem, even when the AVR
is in Standby mode in the main listening room,
press the

Multi

button

and then the Set

button