background image

Installing Traveler Car on Track

Position car at end of track and gently roll on. Car should roll on easily. If not, check to make sure  

you are using CB track. Do not remove ball retaining clips.

 Cars will not roll unless they have 

retaining clips.

 Exception: CB+ cars can convert to non-CB cars. See reverse side.

Position car on edge and gently push one (1) ball 
at a time from center of retaining clip. 

Do not remove retaining clip from car!

Removing Ball Bearings from CB Cars

Position car on edge with retaining clip in place. 
Gently push one (1) ball at a time into car from 
center of clip. Allow balls to roll into return race 
and insert remaining balls. 

Do not overfill car!

Loading Ball Bearings into CB Cars

Ball replacement chart

CB car

Description

Car length

Balls/car

Balls

Order

Balls/set

Ball Ø

3176/3177

Big Boat

5

3

/

8

" (136 mm)

50

Torlon

®

547

25

3

/

8

3178/3179

Big Boat/high-load

7

7

/

16

" (188 mm)

72

Torlon

547

25

3

/

8

Attaching Splice

Pass eye through bail and run tail through to make 

a cow hitch. 

Note:  Insert eye down from above.

Torlon is a registered trademark of Solvay Advanced Polymers.

Содержание 3176









Отзывы: