background image

Printed in USA  4526  01/15

For additional safety, maintenance, and warranty information see www.harken.com/manuals or the Harken catalog.

Maintenance

Warranty

Inspect

Frequently inspect shackles and control block fittings for signs of fatigue. Replace as necessary.  

Make sure every installation includes Harken track endstops. Arrange control tackle so cars do  

not hit endstops under load.

Traveler cars:

 Clean by frequently flushing with fresh water. Periodically clean car by squirting  

a detergent/water solution into center openings. Roll car back and forth to distribute evenly.  

Flush bearings with fresh water.
Do not use spray lubricants because ball bearings can skid, not roll. Apply one (1) to  

two (2) drops of McLube

®

 OneDrop

 ball bearing conditioner to ball contact surfaces of 

track. Roll car back and forth through OneDrop conditioner several times to distribute  

onto bearings. Wipe remaining OneDrop off track. OneDrop conditioner is preferred,  

but you can also use one (1) to two (2) drops of a light machine oil.  

Too much oil attracts dirt.

Track:

 Clean with detergent and water. 

Important! Exposure to some teak cleaners and other caustic solutions can  

result in discoloration of part and is not covered under the Harken warranty.

 

Important! Requires CB+ cars. See complete instructions at www.harken.com/manuals. 

Converting CB + Cars to Run on Non-CB Track

3. Remove retaining clips and  

    corner keepers over box to  

    catch balls

.

1. Use flat-bladed screwdriver  

    to push retaining clip  

    toward end.

5. Remove two (2) clips  

    from car loader. Slide car  

    loader in so loading port  

    is on the side of car  

    without balls.

2. Pry retaining clip off and  

    dump balls in box.

4. Hold car on edge and load  

    lower side with correct  

    number of balls. 

DO NOT  

    OVERLOAD.

 Consult chart  

    to confirm 

quantity.

6. Put one (1) clip on "open"  

    end of loader. Load rest  

    of balls through ball  

    loading port into empty  

    bearing race. Consult  

    chart to confirm quantity.  

    Line up car loader with  

    track and gently roll car  

    onto track.

McLube is a registered trademark of McGee Industries, Inc. 

OneDrop is a trademark of Mclube, a division of McGee Industries, Inc.

Содержание 1635






Отзывы: