Hark HK0522 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 24

Hark HK0522 Скачать руководство пользователя страница 8

8

STEP 3

Locate: Control Panel Assembly [5], two
1/4-20x1/2” Screw [1a] (two remaining from

previous step)
Tools needed: Philips head screwdriver.
Procedure:

— Place the control panel assembly between

the front legs as shown. There are slots on

the control panel that fit around the legs

and line up with the bolt holes.

— Be sure all the tabs on the back side of the

control panel are captured around the legs

as shown below.

— Insert the two remaining screws and tighten

them securely.

STEP 4

Locate: Burner Chamber Assembly [4], three
1/4-20x1/2” Screw [1a] from Hardware Pack - Blister

card.

Tools needed: Philips head screwdriver.
Note: Inspect the burner chamber prior to
assembly to make certain the burner tube is

correctly over the end of the valve as shown:
Procedure:

— Align the burner

chamber assembly [4]

underneath the smoker

as shown.

— Place the body of the

burner chamber assembly so that it sits flush

with the bottom of the cabinet. The mounting

holes and mounting tabs should line up.

— For each mounting hole, insert a 1/4-20x1/2”

screw [1a]. Secure the burner assembly with the

three screws from the inside of the cabinet.

— Securely tighten all three screws.

— Attach the loose igniter wire to the igniter on

the control panel as shown.

5

«
...
6
7
8
9
10
...
»

Содержание HK0522

























Отзывы:

Нет отзывов