Hark HK0522 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 24

Hark HK0522 Скачать руководство пользователя страница 12

12

Step 13

Locate: 2 x Grid Tracks (13), 1 x Water Bowel.
Tools Needed: None
Procedure: Install one grid track (13) in each of the

next holes up from the bottom hole, located in the

grid support for both the left and right hand sides

of the cabinet.

The water bowel is then slid into the grid tracks

to be supported above the wood chip box and lid.

Step 14

Locate: 8 x Grid tracks (13) and 4 x cooking racks

(14)

Tools Needed: None
Procedure:

— Install the remaining grid tracks (13) in the

grid support holes on each side of the cabinet.

Make sure that they are on the same level

hole on each side so that the cooking rack sits

straight.

— Slide a cooking rack(14) into each pair of the

grid tracks to secure the cooking racks at the

desired position.

— Install the woodchip box and water bowl as

shown.

Step 15

Locate: Zip Tie [7d]

Tools needed: None.

Procedure:

— Loop the Zip Tie [7d] through the outside
hole of the front smoker leg [6] as shown.

— Capture the gas hose with the zip tie to
secure it. Do not pull the zip tie too tight - it may
restrict gas flow through the hose.

CAUTION
The wood chip box must be inserted over

the burner during operation. This is to

protect the burner from falling particles,

grease drippings and accidental spill over

from the water bowel.

«
...
10
11
12
13
14
...
»

Содержание HK0522

























Отзывы:

Нет отзывов