Hark HK0522 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 24

Hark HK0522 Скачать руководство пользователя страница 7

7

C. ASSEMBLY INSTRUCTIONS

1

Step 1

Locate: Cabinet (1), lower door (2) and upper door(3)
Note: The doors are attached to the cabinet
Procedure:

— Remove the doors (2) and (3) from the cabinet

(1) by lifting them straight up on the doors to

remove them from the side cabinet hinge. Set the

doors aside.

— Turn the cabinet (1) upside down

STEP 2

Locate: Four Smoker Legs [6], Eight
1/4-20x1/2” Screw [1a] from the Hardware

Pack - Bag A.
Tools needed: Philips head screwdriver.
Procedure:

— Place each leg [6] at the corners of the

smoker Cabinet Assembly [1] as shown.

Fasten each leg [6] with two 1/4-20x1/2”

Screws [1a]. The securing nuts are pre-welded

to the

cabinet.

Note: One leg contains an extra hole on its

side and must be mounted at the front in the

position shown. This hole will be used later to

secure the gas hose to the leg with a zip-tie.

Do not yet insert the two screws in the location

indicated for the front legs. These two screws will

be used in the next assembly steps.

Securely tighten six screws.

4

4

1

13

13

2

3

Leg with extra hole

Leg with extra hole

WARNING

DO NOT HANDLE SMOKER BY THE CROSS BAR ON SMOKER CABINET.

DO NOT LIFT OR MOVE USING THIS CROSS BAR.

«
...
5
6
7
8
9
...
»

Содержание HK0522

























Отзывы:

Нет отзывов