manualshive.com logo in svg

Hardy Process Solutions HI 1756-FC, Руководство пользователя

Поделиться
Скачать
Hardy Process Solutions HI 1756-FC Скачать руководство пользователя страница 49

 
 

44 

 

●

●

●

●

●

 

Chapter 6 

 

If the output is properly wired back to the motor speed controller, verify that the PLC 
analog card parameters for that analog out are set correctly and that the HI 1756-FC 
analog signal is programmed for the corrected controller terminals.  

NOTE 

Hardy Process Solutions Inc. does not provide motor speed control converters or analog 
out PLC modules. Consult the motor speed controller manufacturer’s manual for 
troubleshooting and settings. 

REC +/- settings 

1.

 

The rate exception control indicates whether the controller is running within the 
requested range. If a status bit is out-of-range, the REC status bit is displayed to 
indicate the direction. While this may indicate that the rate is too small for the 
scale’s accuracy or resolution, the reading can be used to determine the effect of 
parameter and mechanical adjustments on improving the material flow control.  

2.

 

During auto rate calibration the PI settings are adjusted to optimize the flow rate 
for your feeder settings and material. The speed of oscillation can be used to 
view the effect of correction or adjustments to the PI settings.  

 

P = 0-100% correction factor. P determines the amount of action or reaction 
that is made in response to an out-of-range rate indication 

 

I = the speed of that action/reaction. This value normally requires only a 
small adjustment. (0.2 increments) If the rate is always high, reduce the I. If 
it is always low, increase I. 

The feeder fails to stop in HOLD, STOP or IDLE 

Determine whether the motor speed control OP% analog card module reacts properly and 
goes to the low setting. 

1.

 

Verify with a multimeter.  

2.

 

Follow the manufacturer’s troubleshooting guide(s) to determine the 
malfunction. 

3.

 

Verify that the Analog out is returning to the low parameter setting as set in the 
PLC menu for that analog out channel. 

NOTE 

Send a Stop or Hold signal when a stop condition occurs. Do not rely on the analog 
signal to stop the feeder. 

System and Load Cell Tests 

Overview of Typical Load Cell System  

The typical load cell system consists of one or more load cells/points and an HI 1756-FC 
Rate Controller. If you have more than one load point, an optional summing junction box 
can read data for individual load cells. 

Load Cell/Sensor/Point

 - is a strain gauge-based force transducer that generates an 

electrical signal proportional to the load applied to the scale. Tension or compression type 
load cells/points can be used to measure pressure, load, or torque.  

Содержание HI 1756-FC

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды