manualshive.com logo in svg

Hardy Process Solutions HI 1756-FC, Руководство пользователя

Поделиться
Скачать
Hardy Process Solutions HI 1756-FC Скачать руководство пользователя страница 35

 
 

30 

 

●

●

●

●

●

 

Chapter 6 

 

capacity is rated at 1000 pounds, the load cell/point will be 10 mVDC at 1000 pounds, 
7.5 mVDC at 750 pounds, 5 mVDC at 500 pounds and so on. 

A zero reference point will 
vary from system to system 
depending on the “Dead Load” 
of the vessel. “Dead Load” is 
the weight of the vessel and 
appurtenances only, with no 
product loaded. In our 
example we will assume the 
dead load to be 500 pounds. 

The operating range for the 
scale in this example is 5-10 
mVDC with a 500 pound 
weight range. Note that after 
zeroing the instrument, the 0 
reading refers to the zero 
reference point and not 
absolute 0 mVDC or absolute 
0 weight. 

 

Millivolts/Weight Scale 

NOTE 

Load cell/point measurements are checked with a digital volt meter at the J1 connector 
on the front of the module or by using INTEGRATED TECHNICIAN with the HI 215IT 
Junction Box. 

Load Check 

Place a load (weight) on the scale or vessel, and check to see if the weight reading on the 
input table changes in the proper direction. 

For example: If the input table display reads 100 pounds and a 20-pound weight is placed 
on the vessel or scale, the ladder logic display should read 120 or some value over 100. 
With the input table display reading 100 pounds, if a 20-pound load is placed on the 
vessel or scale and the reading is 80 pounds, the reading is going in the wrong direction 
and indicates some problem with the system. 

If the input table reads improperly or shows no change, something is wrong with the 
setup. If the input table changes weight in the proper direction, remove the weight and 
proceed to calibrate the module. 

C2 Calibration 

C2® calibration requires C2 load sensors. (If you have no C2 load sensors, see Hard 
Calibration below). The Weigh Module reads the performance characteristics of the 
individual load cells and detects the quantity of load cell(s) in the system. C2 Calibration 
can be performed via Allen Bradley RS LOGIX 5000 using either the output table or 
ladder logic.  

WARNING: 

LOAD CELL CABLE LENGTH HAS BEEN CALCULATED INTO C2 CALIBRATION 
DATA.  HARDY RECOMMENDS THAT YOU DO NOT CUT YOUR ADVANTAGE® or 
ADVANTAGE LITE® LOAD SENSOR CABLES, BECAUSE YOUR C2 ACCURACY  
WILL BE AFFECTED AND THE WARRANTY WILL BE VOIDED. 

Содержание HI 1756-FC

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды