background image

Page 22

For technical questions, please call 1-888-866-5797.

ITEM 59206 

        

SAFETY

SETU
p

Op
ERA
TION

M

AINTENANCE

Long-Term Storage

When the equipment is to remain idle for longer than 

20 days, prepare the Engine for storage as follows:
1. 

CLEANING

Wait for Engine to cool, then clean Engine with 

dry cloth.  

NOTICE:

  

Do not clean using water.

  

The water can cause rust damage over time.  Apply 

a thin coat of rust preventive oil to all metal parts.

2. 

FUEL: 

Gasoline Treatment/Draining the Fuel Tank 

 

To protect the fuel tank during storage, fill the 

tank with fresh gasoline that has been treated 

with a fuel stabilizer additive.  Follow fuel 

stabilizer manufacturer’s recommendations 

for use.  Refer to Checking and Filling Fuel 

Checking and Filling Fuel on page  11.

Aged gasoline that has not been treated with 

stabilizer ahead of time must be safely drained 

away and not run through the engine.

WARNING!

 

TO pREVENT SERIOUS 

INJURY FROM FIRE:

 

Fill tank in a well-ventilated area away 

from ignition sources.  If the engine 

is hot from use, shut the engine off and 

wait for it to cool before adding fuel.  Do not smoke. 

 

Draining the Carburetor

After closing the Fuel Valve, place an appropriate 

container under the Carburetor and carefully 

remove the Drain Bolt from the bottom of the 

Carburetor Bowl, allowing the fuel to drain 

completely.  Replace the Drain Bolt after draining.

WARNING! To prevent serious 

injury and fire, close the Fuel Valve 

before draining the Carburetor.

3. 

LUBRICATION:

a.  Change engine oil.
b.  Clean out area around spark plug.  

Remove spark plug and pour one tablespoon of 

engine oil into cylinder through spark plug hole.

c.  Replace spark plug, but leave 

spark plug cap disconnected.

d.  Pull Starter Handle to distribute oil in cylinder.  

Stop after one or two revolutions when you 

feel the piston start the compression stroke 

(when you start to feel resistance).

4. 

STORAGE AREA: 

Cover and store in a dry, level, well-ventilated 

area out of reach of children.  Storage area should 

also be away from ignition sources, such as 

water heaters, clothes dryers, and furnaces.

5.  Avoid direct exposure to rain and sunlight.

NOTICE:

 During extended storage periods the 

Engine must be started every 3 months and allowed 

to run for 15 – 20 minutes or the Warranty is VOID. 
6. 

AFTER STORAGE: 

Before starting the Engine during or after 

storage, keep in mind that untreated gasoline 

will deteriorate quickly.  Drain the fuel 

tank and change to fresh fuel if untreated 

gasoline has been sitting for a month, if 

treated gasoline has been sitting beyond the 

fuel stabilizer’s recommended time period, 

or if the Engine does not start.

Содержание PREDATOR 59206

































Отзывы: