background image

16

Lowes.com/harborbreeze

OPERATING INSTRUCTIONS

1.  The pull chain on the side of the light kit (J) has four 

positions to control the fan speed. One pull is HIGH, 

two is MEDIUM, three is LOW, and four turns the fan 

OFF. The pull chain in the center of the light kit (J) 

turns the lights ON and OFF.

H

arbor Breez

e

H

arbor Breez

e

2.  Use the fan reverse switch located on the light kit (J) 

to optimize your fan for seasonal performance.
Using a ceiling fan will allow you to raise your 

thermostat setting in summer and lower your 

thermostat setting in winter without feeling a 

difference in your comfort.

Note:

 Wait for the fan to stop before moving the 

reverse switch.
2a. 

In warmer weather,

 push the reverse switch left 

to display a Sun icon, which will result in downward 

airflow creating a wind chill effect.

2b. 

In cooler weather,

 push the reverse switch 

right to display a Snowflake icon, which will result in 

upward airflow that can help move stagnant, hot air off 

the ceiling area.

Important:

 The reverse switch must be set either 

completely left or right in order for the fan to function 

correctly. If the reverse switch is set in the middle 

position, the fan will not operate (Fig. 2c).

Fig. 2a

Fig. 2b

Fig. 2c

2

1

Fan Pull 

Chain

Light Pull 

Chain

J

Reverse 

Switch

Содержание EXOCET 40764




















Отзывы: