background image

English _

15

 

!

OVER

VIEW

Item

Description

a

Illumination Sensor

Detects incoming light to control the IR LED.

b

Lens

Lens for the camera.

c

IR LED

These infrared LED’s are controlled by the illumination sensor.

d

Audio/Alarm cable port

ARM-IN

Used to connect the alarm input sensor or external day/night sensor.

ARM-OUT Used to connect the alarm output signal.

GND

These are common ports to connect alarm input/output signals.

AUDIO IN

Used to connect to a microphone.

e

Reset Button

The button restores all camera settings to the factory default. 
Press and hold for about 5 seconds to reboot the system.

J

    

If you reset the camera, the network settings will be adjusted so that DHCP can be 
enabled. If there is no DHCP server in the network, you must run the Device Manager 
program to change the basic network settings such as IP address, Subnet mask, 
Gateway, etc., before you can connect to the network.

f

Test monitor out port

Output port for test monitoring the video output. Use the test monitor cable to connect to a 
mobile display and check the test video.

g

Zoom/Focus Control Button

T

Zoom in (Tele)

W

Zoom out (Wide)

N

Focusing on a near object (Near)

F

Focusing on a far object (Far)

Focus 
Control

Press this button for automatic focus control.

h

Power Port

Port for power terminal block.

i

Network Port

Used to connect the PoE or Ethernet cable for network connection.

j

Micro SD Card slot

Compartment for the Micro SD card.

Содержание QND-7022R









































Отзывы: