Hanwha Techwin Wisenet TNM-3620TDY Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 22

background image

English _

11

!

INST

ALLA

TION & CONNECTION

Connecting to Audio Input/Output

Speaker

Speaker

Microphone

Microphone

Network

1.

Connect the MIC port of the camera with the microphone or LINE OUT port of the amplifier where the
microphone is connected.

2.

Connect the SPEAKER port of the camera with the speaker or LINE IN port of the amplifier where the
speaker is connected.

3.

Check the specifications for audio input.

~

Audio Codec

- Audio In : G.711 PCM (Bit Rate: 64kbps / Sampling Frequency: 8kHz), G.726 ADPCM (Bit Rate:

16Kbps, 24Kbps, 32Kbps, 40Kbps / Sampling Frequency: 8kHz), AAC (Bit Rate: 48Kbps / Sampling
Frequency: 16kHz)

- Audio Out : G.711 PCM (Bit Rate: 64kbps / Sampling Frequency: 8kHz)

~

Full duplex Audio

~

Audio in

: Selectable (microphone/Line-in), Supported voltage: 2.5VDC (4mA), Input impedance: 2K Ohm

~

Audio out

: Line-out (3.5mm mono jack), Maximum output: 1Vms

~

Line out impedance

: 600Ω

Connecting to the I/O port box

Connect the Alarm I/O cable to the corresponding port of the port box.

Sensor

Alarm

(Warning lamp)

~

ALARM-IN : Used to connect the alarm input sensor or external day/night sensor.

~

ALARM-OUT : Used to connect the alarm output signal.

~

GND : Common ground port for alarm in/output signal.

J

`

If devices (e.g., flashing light and siren) that exceed the voltage and current specifications are connected by using the open
collector method, it may cause malfunction.
Refer to the “

Alarm Out Wiring Diagram

” when connecting devices such as a warning lamp or a siren.

«
...
9
10
11
12
13
...
»

Содержание Wisenet TNM-3620TDY























Отзывы:

Нет отзывов

Похожие инструкции для Wisenet TNM-3620TDY

Бренд: FLIR Страницы: 150

Бренд: Alpine Страницы: 4

Бренд: MISUMI Страницы: 15

Бренд: Papago Страницы: 17

Бренд: Vantrue Страницы: 43

Бренд: wikango Страницы: 26

Бренд: Reed Instruments Страницы: 20

Reviw Miro GPS Recorder

Бренд: Android Страницы: 38

Бренд: Vantrue Страницы: 287

Бренд: Parksafe Страницы: 8

Бренд: Abask Страницы: 153

Бренд: Videofied Страницы: 4

Бренд: Transtyle Страницы: 12

Black Eye Max-II

Бренд: Elsrod Страницы: 40

Бренд: Gazelle Страницы: 41

61-844 HeatSeeker

Бренд: IDEAL Страницы: 22

A129 Plus Duo IR

Бренд: Viofo Страницы: 15

Бренд: Viofo Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды