background image

web viewer

18_

 web viewer

web viewer

CONNECTING TO THE CAMERA

Normally, you would

1. 

Launch the Internet browser.

2. 

Type the IP address of the camera in the address bar. 
ex) • IP address (IPv4) : 192.168.1.100 

;

 

http://192.168.1.100 
- the Login dialog should appear. 
• IP address (IPv6) : 2001:230:abcd: ffff:0000:0000:ffff:1111 

;

 http://[2001:230:abcd:ffff:0000:0000:ffff:1111] - the Login 

dialog should appear.

If the HTTP port is not 80

1. 

Launch the Internet browser.

2. 

Type the IP address and HTTP port number of the camera in the address bar. 
ex) IP address : 192.168.1.100:HTTP Port number(8080)  

;

 http://192.168.1.100:8080 - the Login dialog should appear.

Using URL

1. 

Launch the Internet browser.

2. 

Type the DDNS URL of the camera in the address bar. 
ex) URL address : http://ddns.hanwha-security.com/ID 
- the Login dialog should appear.

 

J

 

`

Network connection is disabled in the LAN only environment.

Connecting via UPnP

1. 

Run the client or operating system to support the UPnP protocol.

2. 

Click the camera name for search. 
In the Windows operating system, click the camera name searched from the network menu.

 

- The login window is displayed.

Connecting via Bonjour

1. 

Run the client or operating system to support the Bonjour protocol.

2. 

Click the camera name for search. 
In the Mac operating system, click the camera name searched from the Bonjour tab of Safari.

 

- The login window is displayed.

To check the DDNS address

If the camera is connected directly to the DHCP cable modem, DSL modem, the IP address of your network 
will be changed each time you try to connect to the ISP (Internet Service Provider) server. 
In this case, you will not be informed of the IP address changed by DDNS.
Once you register a dynamic IP-based device with the DDNS server, you can easily check the changed IP 
when you try to access the device. 
To register your device to the <

DDNS

> server, visit http://ddns.hanwha-security.com and register your device 

first, and then set the Web Viewer’s <

Network

> - <

DDNS

> to <

Wisenet DDNS

>, as well as providing 

<

Product ID

> that had been used for DDNS registration.

Содержание Wisenet TNM-3620TDY























Отзывы: