Hantek HDG3000B Series Скачать руководство пользователя страница 26

Страница: 26 / 102

Quick start

Figure 4.2 Top view

4.3

Preparation before use

4.3.1 Connect the power supply

Connect the power cord as needed.

The input AC power specifications of this series of signal generators are: 100-120 VAC

(±10%), 45-440 Hz or 120-240 VAC (±10%), 45-66Hz. Please use the supplied power

cord to connect the machine to AC power.

Press the power switch in the lower left corner of the front panel to turn on the

instrument. If the instrument does not turn on, verify that the power cord is securely

connected and that the instrument is connected to a live power source.

Switch

：

To turn off the instrument, press the power switch.

Warning

：

To avoid electric shock, make sure the instrument is properly grounded.

Содержание HDG3000B Series







































































































Результаты поиска

Содержание HDG3000B Series

Отзывы:

Похожие инструкции для HDG3000B Series

Бренды по названию

Популярные бренды

Hantek HDG3000B Series, Руководство пользователя

Результаты поиска

Содержание HDG3000B Series

Отзывы:

Похожие инструкции для HDG3000B Series

Бренды по названию

Популярные бренды