Hantek DPO6000 Series Скачать руководство пользователя страница 7

Страница: 7 / 116

DPO6000

，

MPO6000 Series Digital Phosphor Oscilloscope Instruction V1.1

- 5 -

WARNING

This oscilloscope can only be used for measurements within its specified

measurement categories.

Measurement Category Definitions

Measurement category I

is for measurements performed on circuits not directly

connected to MAINS. Examples are measurements on circuits not derived from MAINS,

and specially protected (internal) MAINS derived circuits. In the latter case,transient

stresses are variable. For that reason, the transient withstand capability of the equipment

is made known to the user.

Measurement category II

is for measurements performed on circuits directly connected

to low voltage installations. Examples are measurements on household appliances,

portable tools and similar equipment.

Measurement category III

is for measurements performed in building installations.

Examples are measurements on distribution boards, circuit-breakers, wiring(including

cables, bus-bars, junction boxes, switches and socket-outlets) in fixed installations,

equipment for industrial use and some other equipment. For example,stationary motors

with permanent connection to a fixed installation.

Measurement category IV

is for measurements performed at the source of a low-voltage

installation. Examples are electricity meters and measurements on primary overcurrent

protection devices and ripple control units.

Ventilation Requirement

This oscilloscope uses fan to force cooling. Please make sure that the air intake and

exhaust areas are free from obstructions and have free air. When using the oscilloscope

in a bench-top or rack setting, provide at least 10 cm clearance beside,above and behind

the instrument for adequate ventilation.

WARNING

Inadequate ventilation may cause a temperature increase which can damage

the instrument.So please keep the instrument well ventilated during operation

and inspect the intake and fan regularly.

Working Environment

Temperature

Operating: 0

℃

to +50

℃

Non-operating: -40

℃

to +70

℃

Humidity

℃

to +30

℃

: ≤95% relative humidity

+30

℃

to +40

℃

: ≤75% relative humidity

+40

℃

to +50

℃

: ≤45% relative humidity

WARNING

To avoid short circuits inside the instrument or electric shocks, please do not

operate in humid environment.

Altitude

Operating: below 3 km

Non-operating: below 15 km

Care and Cleaning

Care

Содержание DPO6000 Series





















































































































Результаты поиска

Содержание DPO6000 Series

Отзывы:

Похожие инструкции для DPO6000 Series

Бренды по названию

Популярные бренды

Hantek DPO6000 Series, Руководство пользователя

Результаты поиска

Содержание DPO6000 Series

Отзывы:

Похожие инструкции для DPO6000 Series

Бренды по названию

Популярные бренды